Description
The Composite Spurious Emission Requirement is an RF transmitter requirement defined in 3GPP TS 36.101 for LTE user equipment and referenced in TS 36.833 for conformance testing. It applies to intraband non-contiguous carrier aggregation, where a UE transmits on multiple component carriers within the same operating band separated by gaps. Spurious emissions are unwanted emissions generated by the transmitter that fall outside the necessary bandwidth, including harmonics, intermodulation products, and other non-linear artifacts. The composite spurious emission requirement defines the overall limit on such emissions when multiple separated sub-blocks are active simultaneously, and it is constructed as a combination of the individual sub-block spurious emission requirements.
Conceptually, the requirement parallels the composite spectrum emission mask but addresses a different frequency domain. While the spectrum emission mask governs emissions close to the carrier — the out-of-band domain — spurious emission requirements govern emissions far from the carrier, typically in other bands or at large frequency offsets. When a UE operates non-contiguous CA, each sub-block generates its own spurious products, and these can combine or overlap in complex ways. The composite requirement aggregates the individual sub-block limits to produce a single bound that the total spurious emission of the UE must satisfy across the relevant measurement ranges.
The construction of the composite requirement is analogous to the composite SEM: at each frequency of interest, the applicable sub-block spurious emission requirements are combined to form an envelope. This ensures that the aggregate spurious emission from all active sub-blocks does not exceed acceptable levels, protecting other radio systems, other operators' spectrum, and the UE's own receiver from interference. Because spurious emissions can fall in widely separated frequency ranges — for example, harmonics landing in other licensed bands — the requirement is specified over broad frequency ranges and is often expressed as absolute power limits or as limits relative to the wanted signal power.
In the network, the composite spurious emission requirement is part of the coexistence framework that allows LTE-Advanced UEs to operate in a crowded spectrum environment. It is verified in transmitter conformance tests where the UE is configured for the relevant non-contiguous CA combination and its emissions are measured across the specified ranges. The standard provides detailed tables of applicable limits per band and CA configuration.
Like the composite SEM, the composite spurious emission requirement has a definition that is unchanged from Rel-12 through Rel-20. The stability of the definition reflects the enduring physical principle: aggregate unwanted emissions from separated sub-blocks must be bounded. New bands and CA combinations are added over time, but the conceptual framework remains constant, underscoring its robustness as a foundational RF coexistence requirement.
Purpose & Motivation
The composite spurious emission requirement was created to address the coexistence challenges introduced by intraband non-contiguous carrier aggregation. Spurious emissions are inherently a coexistence concern: they can fall into other operators' spectrum, into bands used by other radio technologies, or into the UE's own receive bands, causing interference. When a UE transmits on a single contiguous block, the spurious emission requirement for that block is well understood. But with non-contiguous aggregation, multiple sub-blocks each contribute spurious products, and the aggregate effect must be controlled.
Defining a composite requirement solves this by providing a single, rigorous bound derived from the individual sub-block requirements. This modular approach avoids the need to define unique spurious emission limits for every possible non-contiguous CA arrangement, which would be impractical given the combinatorial explosion of carrier positions and gap sizes. Instead, the standard combines the sub-block limits into an envelope that the aggregate emission must satisfy.
The requirement protects a wide range of stakeholders. Regulators rely on it to ensure UEs comply with emission limits that protect other spectrum users. Operators depend on it to avoid interference with adjacent spectrum and with their own networks. UE vendors use it as a design target for filtering, linearity, and harmonic suppression. The fact that the definition has remained unchanged from Rel-12 to Rel-20 demonstrates that the original formulation successfully addressed the problem and continues to serve as a stable foundation for LTE-Advanced RF conformance.
What changed in its specifications
The latest release-to-release comparison of specifications that define Composite spurious emission requirement. Each summary describes the whole specification, not only this term.
Rel-13 added carrier aggregation requirements, 4Rx antenna port tests, MTC coverage enhancements, LAA test parameters, FD-MIMO procedures, and downlink interference mitigation requirements.
Full comparison in TS 36.101 →Release Timeline
Evolution Across Releases
An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.
Defining Specifications
3GPP specifications that define or reference Composite spurious emission requirement, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 36.101 vk10 | E-UTRA UE RF Requirements | Rel-20 read |
| TS 36.833 | 3GPP TR 36.833 | Rel-12 read |