Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Physical Layer

IAB-DU channel bandwidth

Integrated Access and Backhaul Distributed Unit Channel Bandwidth

Physical Layer →

IAB-DU channel bandwidth is the RF bandwidth supporting a single IAB-DU RF carrier with the transmission bandwidth configured in the uplink or downlink, defining the spectral resources for the access link of an IAB-node's DU.

Introduced
Rel-16
Where
Radio Access Network › NG-RAN (5G)
Specifications
2 specs
IAB-DU channel bandwidth Description Purpose Neighbours Specifications

Description

The IAB-DU channel bandwidth is a radio frequency (RF) parameter that defines the bandwidth of a single RF carrier transmitted or received by the distributed unit (DU) function of an IAB-node. It is the RF bandwidth supporting a single IAB-DU RF carrier with the transmission bandwidth configured in the uplink or downlink. In the IAB architecture, an IAB-node contains both a mobile termination (MT) and a DU. The MT communicates with the parent node (which could be the IAB-donor-DU or another IAB-node), while the DU communicates with child IAB-nodes and user equipment (UE). The IAB-DU channel bandwidth thus refers to the bandwidth used by the DU for its access link, i.e., the link between the IAB-node and its served UEs or child IAB-nodes.

The IAB-DU channel bandwidth is defined in the RF specifications TS 38.174 (NR repeater) and TS 38.176 (NR IAB). These specifications define the RF requirements for IAB nodes, including the channel bandwidth, output power, and unwanted emissions. The channel bandwidth is a key parameter for the design and operation of the IAB-node's radio interface. It determines the maximum transmission bandwidth that can be configured in the uplink or downlink, and it affects the achievable data rates and coverage.

The IAB-DU channel bandwidth is typically configured by the network during the setup of the IAB-node. It must be compatible with the capabilities of the IAB-node's RF hardware and with the spectrum allocation of the operator. The IAB-DU channel bandwidth can be the same as or different from the channel bandwidth used by the MT for the backhaul link. In some cases, the IAB-node may operate in a full-duplex mode or use time-division multiplexing between the access and backhaul links, which imposes additional constraints on the channel bandwidth and the RF design.

The IAB-DU channel bandwidth is an important parameter for the physical layer design of the IAB-node. It affects the selection of the fast Fourier transform (FFT) size, the number of resource blocks, and the guard band. It also influences the RF requirements such as the error vector magnitude (EVM), the adjacent channel leakage ratio (ACLR), and the spurious emissions. The IAB-DU channel bandwidth must be carefully chosen to balance performance, cost, and spectrum efficiency.

In summary, the IAB-DU channel bandwidth is a fundamental RF parameter that defines the spectral resources available to the DU function of an IAB-node. It is specified in 3GPP TS 38.174 and TS 38.176 and is essential for the design and operation of IAB networks.

Purpose & Motivation

The IAB-DU channel bandwidth parameter exists to define the RF bandwidth of the access link of an IAB-node's DU, ensuring that the IAB-node's radio interface meets the necessary performance and regulatory requirements. In traditional base stations, the channel bandwidth is a well-defined parameter that determines the transmission bandwidth and the RF requirements. For IAB-nodes, which have both an access link (DU) and a backhaul link (MT), the channel bandwidth of the DU is a critical parameter that affects the overall performance of the IAB topology. It allows the network to configure the IAB-node's DU to operate on a specific carrier with a specific bandwidth, matching the spectrum allocation and the capabilities of the IAB-node.

Before the introduction of IAB in Release 16, relay nodes in LTE had limited RF requirements and often used the same carrier for both access and backhaul. The IAB architecture, with its integrated access and backhaul, required a more sophisticated RF design to support simultaneous operation of the MT and DU, potentially on different frequencies or with different bandwidths. The IAB-DU channel bandwidth parameter was created to provide a clear definition of the DU's RF bandwidth, enabling the specification of RF requirements for IAB nodes in TS 38.176. This allows operators to deploy IAB-nodes with confidence that they meet the necessary performance and regulatory standards.

In summary, the IAB-DU channel bandwidth was created to meet the need for a standardized RF parameter for the access link of IAB-nodes. It enables the specification of RF requirements, facilitates the configuration of IAB-nodes, and ensures that IAB deployments can achieve the desired performance and comply with regulations.

Release Timeline

Evolution Across Releases

An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.

Rel-16 Initial

Initial definition introduced with the IAB architecture. The IAB-DU channel bandwidth is defined as the RF bandwidth supporting a single IAB-DU RF carrier with the transmission bandwidth configured in the uplink or downlink. This established the fundamental RF parameter for the access link of IAB-nodes, enabling the specification of RF requirements in TS 38.174 and TS 38.176.

The definition text carried over unchanged from Rel-16. The IAB-DU channel bandwidth continued to be defined as the RF bandwidth supporting a single IAB-DU RF carrier with the transmission bandwidth configured in the uplink or downlink, with no changes to its wording.

The definition text carried over unchanged from Rel-16. The IAB-DU channel bandwidth remained the RF bandwidth supporting a single IAB-DU RF carrier with the transmission bandwidth configured in the uplink or downlink, with no modifications to its definition.

The definition text carried over unchanged from Rel-16. The IAB-DU channel bandwidth continued to be defined as the RF bandwidth supporting a single IAB-DU RF carrier with the transmission bandwidth configured in the uplink or downlink, with no changes to its wording.

The definition text carried over unchanged from Rel-16. The IAB-DU channel bandwidth remained the RF bandwidth supporting a single IAB-DU RF carrier with the transmission bandwidth configured in the uplink or downlink, with no modifications to its definition.

Defining Specifications

3GPP specifications that define or reference IAB-DU channel bandwidth, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 38.174 vk00 NR Integrated Access and Backhaul Requirements Rel-20 read
TS 38.176 vj40 IAB Conformance Testing Rel-19 read