Description
INACTIVE is a special Absolute Grant (AG) value transmitted by the serving cell's scheduler on the E-DCH Absolute Grant Channel (E-AGCH) in HSPA (HSUPA). It is defined in TS 25.319 and TS 25.321 and serves multiple control purposes depending on the UE's state. In CELL_DCH, the INACTIVE value can be sent to deactivate a specific HARQ process or to switch the UE to its secondary E-RNTI. In CELL_FACH (FDD only), the same INACTIVE value can be sent to release a common E-DCH resource. The term therefore denotes a reserved, special-purpose grant value rather than a normal scheduling grant.
The E-AGCH is a downlink physical channel that carries Absolute Grants from the NodeB scheduler to the UE, telling it the maximum E-DPDCH power ratio it may use. The Absolute Grant is encoded as a 5-bit value (with additional fields such as the scope and the E-RNTI), and one of the reserved codepoints is the INACTIVE value. When the UE receives an Absolute Grant with the INACTIVE value, it does not interpret it as a scheduling grant; instead it performs the control action associated with that state. This dual-purpose use of a reserved grant codepoint is an efficient design: it reuses the existing grant signalling channel rather than requiring a separate control channel.
In CELL_DCH, the INACTIVE value is used for HARQ process management and E-RNTI switching. Deactivating a HARQ process via INACTIVE allows the scheduler to stop the UE from transmitting on a particular process without tearing down the E-DCH configuration. Switching the UE to its secondary E-RNTI is used in multi-carrier and dual-cell HSUPA scenarios, where the secondary E-RNTI identifies the UE for a secondary uplink frequency or cell. The INACTIVE value thus acts as a mode-switch signal within the E-AGCH framework.
In CELL_FACH (FDD only), the INACTIVE value is used to release a common E-DCH resource. In the enhanced CELL_FACH state, UEs use common E-DCH resources for uplink transmission without a dedicated connection. When the network wants to release that common resource (e.g., due to inactivity or resource pressure), it sends the INACTIVE Absolute Grant on the E-AGCH, and the UE releases the common E-DCH resource and returns to a state without enhanced uplink. This provides a lightweight release mechanism without dedicated RRC signalling.
The INACTIVE value is therefore a small but important element of HSUPA radio resource control. It illustrates how 3GPP reuses reserved codepoints in grant channels to carry control semantics, reducing signalling overhead and enabling fast scheduler-driven control. For engineers working on HSPA scheduling, HARQ management, dual-cell HSUPA, or enhanced CELL_FACH, understanding the INACTIVE value is essential for correct implementation of the E-AGCH procedures.
Purpose & Motivation
INACTIVE exists to provide a fast, low-overhead control mechanism within the HSUPA grant signalling framework. The E-AGCH carries Absolute Grants from the NodeB scheduler to the UE, and reserving one codepoint as INACTIVE allows the scheduler to signal control actions — HARQ process deactivation, secondary E-RNTI switching, and common E-DCH resource release — without defining separate physical channels or additional RRC signalling. This is important because HSUPA scheduling is fast and dynamic, and control actions must be delivered with the same latency as normal grants.
The concept solves several problems. First, HARQ process management: the scheduler needs a way to deactivate individual processes without reconfiguring the UE. Second, multi-carrier operation: switching to a secondary E-RNTI must be signalled quickly. Third, enhanced CELL_FACH: releasing a common E-DCH resource must be lightweight, since UEs in CELL_FACH may not have a dedicated RRC connection suitable for heavier signalling. By reusing a reserved grant codepoint, 3GPP achieved all three with minimal specification and implementation complexity.
Its definition has remained unchanged from Rel-8 through Rel-19, reflecting the stability of the HSUPA grant framework. Even as HSPA evolved with dual-cell and multi-carrier features, the INACTIVE semantics were preserved, demonstrating the durability of the original design.
What changed in its specifications
The latest release-to-release comparison of specifications that define INACTIVE. Each summary describes the whole specification, not only this term.
Added two E-DCH interference mitigation sub-features: radio links without DPCH/F-DPCH and serving E-DCH cell decoupling. Also added Implicit Grant handling for Secondary Serving E-DCH cells.
Full comparison in TS 25.319 →Rel-16 brings only minor changes to TS 25.321: 0 clauses changed, with no change attributed to a release feature.
Full comparison in TS 25.321 →Release Timeline
Evolution Across Releases
An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.
Defining Specifications
3GPP specifications that define or reference INACTIVE, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 25.319 vj00 | Enhanced Uplink for UTRA FDD/TDD | Rel-19 read |
| TS 25.321 vj00 | MAC Protocol Specification for UTRAN | Rel-19 read |