Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Physical Layer

LPF

Low Pass Filter

Physical Layer →

LPF is a Low Pass Filter, a signal processing component that passes low-frequency signals while attenuating frequencies above a cutoff point, used in NR radio transmission and reception for filtering, spectral shaping, and interference control.

Introduced
Rel-18
Where
Radio Access Network › NG-RAN (5G)
Specifications
2 specs
LPF Description Purpose Neighbours Specifications

Description

A Low Pass Filter (LPF) is a fundamental signal-processing building block used throughout the physical layer of 3GPP radio systems. Its defining behaviour is to pass signal components below a chosen cutoff frequency with minimal attenuation while progressively attenuating components above that cutoff. In the 3GPP context, LPFs appear in the transmit and receive chains of the NR base station and UE, where they are used for pulse shaping, image rejection, spectral confinement and noise suppression. The filter may be implemented in the analogue domain (e.g., as part of the RF front end) or digitally (e.g., as a finite impulse response or infinite impulse response filter in baseband processing).

In the transmit direction, an LPF is typically placed after digital-to-analogue conversion or after up-conversion to suppress out-of-band emissions and to shape the transmitted spectrum so that it complies with the operating band unwanted emission limits and the spectrum emission mask defined in the RF specifications. In the receive direction, an LPF is used to reject high-frequency noise, blockers and aliasing components before sampling, thereby protecting the analogue-to-digital converter and improving the effective signal-to-noise ratio. The choice of cutoff frequency and filter order involves a trade-off between passband flatness, transition bandwidth, stopband attenuation, group delay and implementation complexity.

Within 3GPP, the LPF is not usually specified as a normative algorithm but rather as a component whose effects are captured in RF requirement specifications such as 38.774 (NR repeater and other radio equipment) and 38.869 (NR radio equipment performance). These specifications define the transmitter and receiver characteristics that the overall equipment must meet, and the LPF is one of the means by which those characteristics are achieved. For example, the filter contributes to the adjacent channel leakage ratio (ACLR), the spectrum emission mask, the spurious emission limits and the receiver blocking and selectivity performance. Because the exact filter design is implementation-specific, 3GPP requirements are expressed as measurable performance limits rather than as a prescribed filter topology.

In Rel-18 and Rel-19, the LPF concept remains relevant as NR evolves toward wider bandwidths, higher frequency ranges (FR2 and beyond) and more complex multi-antenna architectures. Wider signal bandwidths increase the demands on filtering to avoid aliasing and spectral regrowth, while higher carrier frequencies make analogue filter design more challenging. The LPF therefore remains a key enabler for meeting the increasingly stringent RF performance requirements of modern NR equipment.

Purpose & Motivation

The Low Pass Filter exists to control the spectral content of signals in the radio transceiver chain. Without adequate low-pass filtering, transmitters would emit excessive out-of-band energy that could interfere with adjacent channels and violate regulatory and 3GPP spectrum emission requirements, while receivers would suffer from aliasing, noise and blocker-induced degradation. The LPF provides a practical, well-understood means of shaping the signal spectrum and protecting sensitive components such as ADCs and DACs.

Historically, as cellular systems moved from narrowband to wideband and then to very wideband operation, the demands on filtering increased. Early systems could rely on relatively simple analogue filters, but the wide bandwidths of NR, especially in FR2, require carefully designed filters with sharp transition bands and high stopband attenuation. The LPF concept has therefore evolved from a simple analogue component into a carefully engineered element of the digital and analogue front end.

In 3GPP specifications, the LPF is not mandated as a specific design but is implicitly required through performance requirements. Its purpose in the standards context is to ensure that equipment can meet emission and reception quality targets. The Rel-18/19 references in 38.774 and 38.869 reflect the continued importance of filtering as NR equipment addresses new bands, wider bandwidths and more demanding coexistence scenarios.

Release Timeline

Evolution Across Releases

An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.

Rel-18 Initial

Initial introduction of LPF references in NR RF specifications 38.774 and 38.869, reflecting the need for filtering in wideband NR equipment and higher frequency ranges.

The term carried over unchanged from Rel-18; no definition text revision was indicated in the available data.

Defining Specifications

3GPP specifications that define or reference LPF, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 38.774 vj20 RF Requirements for Low-Power Wake-up Signal and Receiver Rel-19 read
TR 38.869 vi00 Study on low-power wake up signal and receiver for NR Rel-18 read