Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Radio Access Network

PRS-only TP

Positioning Reference Signal-only Transmission Point

Radio Access Network →

PRS-only TP is a transmission point that broadcasts only PRS or DL-PRS signals for OTDOA-based positioning, is not associated with any cell, and enhances positioning accuracy in E-UTRA and NR networks by providing dedicated reference signals.

Introduced
Rel-14
Where
Radio Access Network › E-UTRAN (LTE)
Specifications
5 specs
PRS-only TP Description Purpose What changed Neighbours Detected Changes Specifications

Description

A PRS-only Transmission Point (TP) is a specialized network node defined in 3GPP specifications for positioning purposes. Unlike a conventional base station (eNB or gNB), a PRS-only TP does not carry any user data or control-plane traffic; it exclusively transmits Positioning Reference Signals (PRS) in E-UTRA or Downlink PRS (DL-PRS) in NR. This allows the network to deploy additional positioning beacons without the overhead of full cell functionality, improving the hearability of reference signals for Observed Time Difference of Arrival (OTDOA) and other PRS-based positioning methods.

The concept was introduced in Release 14 to support enhanced positioning performance for E-UTRA, particularly for indoor and dense urban scenarios where traditional cell-based PRS transmission may suffer from interference or insufficient coverage. A PRS-only TP is not associated with a cell, meaning it does not broadcast cell-specific reference signals, synchronization signals, or system information. Instead, it is configured and managed as part of the positioning architecture, with its location and PRS configuration known to the E-SMLC (Evolved Serving Mobile Location Center) or LMF (Location Management Function).

In operation, the E-SMLC/LMF provides assistance data to the UE, including the PRS configuration of PRS-only TPs, so that the UE can measure the reference signal time difference (RSTD) between PRS-only TPs and regular cells. The UE then reports these measurements to the location server, which computes the position using OTDOA. Because PRS-only TPs are not tied to a cell, they can be deployed flexibly—for example, on building walls or ceilings—to provide dedicated positioning coverage without affecting the radio access network's cell planning.

From Release 16 onwards, the definition was updated to include DL-PRS, extending the concept to NR positioning. This allows PRS-only TPs to be used in both E-UTRA and NR contexts, supporting multi-RAT positioning and the enhanced positioning requirements of 5G. The PRS-only TP remains a key enabler for high-accuracy positioning in 3GPP networks, particularly for industrial IoT and emergency services.

Purpose & Motivation

The PRS-only TP was created to address the limitations of traditional cell-based PRS transmission in OTDOA positioning. In conventional networks, PRS are transmitted by regular cells, but their hearability can be poor due to interference, cell density, or physical obstructions. Deploying additional full cells solely for positioning would be costly and complex. A PRS-only TP solves this by providing a low-cost, dedicated positioning beacon that transmits only PRS, improving the geometry and hearability for positioning measurements without impacting the radio access network's capacity or coverage planning.

Historically, Release 9 introduced PRS for E-UTRA to support OTDOA, but performance was often limited by the lack of sufficient detectable PRS from multiple cells. Release 14 enhanced positioning with the introduction of PRS-only TPs, allowing operators to deploy additional positioning nodes where needed. This was particularly important for indoor positioning and emergency call location, where accuracy requirements are stringent. The extension to DL-PRS in Release 16 ensures that the concept evolves with 5G NR positioning, supporting the higher accuracy and lower latency requirements of 5G use cases such as industrial automation and autonomous vehicles.

What changed in its specifications

The latest release-to-release comparison of specifications that define PRS-only TP. Each summary describes the whole specification, not only this term.

TS 36.305Rel-11 → Rel-12

Added BeiDou Navigation Satellite System (BDS) support for UTRA and LTE. Added GERAN and UTRAN measurement results to RF pattern matching positioning data transferred from eNodeB to E-SMLC.

Full comparison in TS 36.305 →
TS 36.355Rel-11 → Rel-12

Added support for BeiDou Navigation Satellite System (BDS) for UTRA and LTE, adding BeiDou-specific GNSS assistance data to LTE positioning procedures.

Full comparison in TS 36.355 →

Release Timeline

Detected Changes Across Releases

from 3GPP Change Requests

Specific changes extracted from the „Change history“ tables of 3GPP specifications (1 CRs across 1 releases). Complements the general historical overview above with the evidence-based evolution of this function.

Rel-16 1 change

Defining Specifications

3GPP specifications that define or reference PRS-only TP, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 36.305 vj00 UE Positioning in E-UTRAN Stage 2 Rel-19 read
TS 36.355 vj00 LTE Positioning Protocol (LPP) Rel-19 read
TS 36.455 vj00 LTE Positioning Protocol Annex (LPPa) Rel-19 read
TS 37.355 vj30 LTE Positioning Protocol (LPP) Rel-19 read
TS 38.305 vj30 NG-RAN UE Positioning Stage 2 Rel-19 read