Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Services

Receive Only Mode

Receive Only Mode (eMBMS)

Services →

Receive Only Mode is a UE configuration allowing reception of eMBMS broadcast services without PLMN registration or USIM, enabling free-to-air reception on standardized TMGI ranges while prohibiting all mobility management signalling.

Introduced
Rel-14
Where
Services › IMS
Specifications
5 specs
Receive Only Mode Description Purpose What changed Neighbours Detected Changes Specifications

Description

Receive Only Mode (ROM) is a UE configuration option introduced in 3GPP Release 14 that enables a device to receive evolved Multimedia Broadcast Multicast Service (eMBMS) content without establishing any relationship with the Public Land Mobile Network (PLMN) that is broadcasting the service. In conventional eMBMS operation, a UE must attach to the network, perform registration, and maintain NAS and RRC signalling with the serving PLMN in order to receive broadcast or multicast services. Receive Only Mode removes this requirement entirely, allowing a device to act as a pure broadcast receiver that passively consumes eMBMS transmissions.

The mechanism operates by exploiting the broadcast nature of eMBMS. eMBMS data is transmitted over the air interface using MBMS Single Frequency Network (MBSFN) or Single-Cell Point-to-Multipoint (SC-PTM) techniques, and the scheduling information is carried in System Information Blocks (SIBs) — specifically SIB2, SIB13, and SIB15 for MBSFN, and SIB20 for SC-PTM. A UE in Receive Only Mode acquires these SIBs by reading the broadcast channel of the cell without performing any access stratum or non-access stratum signalling. It then uses the acquired system information to tune to the MBMS radio bearers and decode the broadcast content. Because no registration occurs, the network has no knowledge of the device's presence, and the device consumes no signalling resources beyond passive reception.

A critical constraint of Receive Only Mode is that the UE may only receive MBMS services identified by a standardized TMGI (Temporary Mobile Group Identity) value range. This restriction ensures that only services intended for open, unauthenticated reception — such as public safety alerts, emergency broadcasts, or free-to-air content — are accessible in this mode. Services requiring subscription or authorization use TMGIs outside this standardized range and therefore cannot be received by a ROM device. This design prevents unauthorized access to protected content while enabling legitimate broadcast use cases.

The mode explicitly prohibits the UE from performing any Mobility Management procedures or other signalling with the network offering the eMBMS service. This means no Attach, no Tracking Area Update, no Service Request, and no RRC connection establishment toward that PLMN. The UE behaves as a receive-only listener. Notably, the use of Receive Only Mode does not require a USIM, which is a significant departure from normal cellular operation where USIM-based authentication is mandatory. This makes ROM suitable for embedded devices, dedicated broadcast receivers, and scenarios where provisioning a subscription is impractical or unnecessary.

Receive Only Mode is specified across a range of 3GPP documents. TS 23.246 defines the overall MBMS architecture and the service-level requirements for ROM. TS 23.746 and TS 23.757 address MBMS and related broadcast service aspects, while TS 26.346 specifies the MBMS codecs and media delivery formats that a ROM receiver must support. TS 36.300 provides the E-UTRAN access stratum description, including how the UE acquires system information and configures the MBMS radio bearers without an RRC connection. Together these specifications ensure interoperability between ROM devices and any compliant eMBMS network.

Purpose & Motivation

Receive Only Mode exists to solve a fundamental mismatch between the broadcast nature of eMBMS and the connection-oriented, subscription-based model of cellular networks. eMBMS was designed to deliver the same content efficiently to many users simultaneously, but the traditional requirement for PLMN registration and USIM authentication meant that every receiver had to be a fully provisioned subscriber. This limited the reach of broadcast services to devices with active subscriptions and imposed signalling overhead on the network for devices that only wanted to listen.

Before Release 14, there was no standardized way for a device to receive eMBMS content without attaching to the network. This was particularly problematic for public safety and emergency broadcast scenarios, where devices such as dedicated receivers, alerting devices, or visitor terminals might need to receive critical information without a subscription. It also constrained the commercial viability of free-to-air broadcast services over cellular, since content providers could not reach unsubscribed audiences.

Receive Only Mode addresses these limitations by defining a clean separation between broadcast reception and network attachment. It enables free-to-air and public-interest broadcast reception, supports devices without USIMs, eliminates signalling load from passive receivers, and provides a standardized framework — anchored on the standardized TMGI range — that protects operator services while enabling open broadcast access. The mode has been carried forward essentially unchanged through Releases 15 to 19, reflecting its stable and well-understood design.

What changed in its specifications

The latest release-to-release comparison of specifications that define Receive Only Mode. Each summary describes the whole specification, not only this term.

TS 23.246Rel-18 → Rel-19

Rel-19 brings only minor changes to TS 23.246: 0 clauses changed, with no change attributed to a release feature.

Full comparison in TS 23.246 →
TS 26.346Rel-16 → Rel-17

Added a profiled FLUTE FDT schema with semantics and versioning, plus 5GMS references and requirements, removing old schema clauses. Updated User Service Bundle Description schema versions and added a new unicast announcement FQDN format.

Full comparison in TS 26.346 →

Release Timeline

Detected Changes Across Releases

from 3GPP Change Requests

Specific changes extracted from the „Change history“ tables of 3GPP specifications (1 CRs across 1 releases). Complements the general historical overview above with the evidence-based evolution of this function.

Rel-15 1 change
  • MBMS reception in Receive Only Mode TS 36.300CR1207

Defining Specifications

3GPP specifications that define or reference Receive Only Mode, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 23.246 vj00 MBMS Bearer Service Stage 2 Description Rel-19 read
TS 23.746 ve00 Feasibility Study on Enhanced TV Services over 3GPP Rel-14 read
TR 23.757 vh00 5G MBS Architectural Enhancements Study Rel-17 read
TS 26.346 vj30 MBMS User Services Specification Rel-19 read
TS 36.300 vj20 E-UTRAN Radio Interface Protocol Architecture Rel-19 read