Description
Reference Signal Antenna Power (RSAP) is a physical layer parameter that specifies the power of reference signals transmitted from each antenna port in a cellular network. It is used by user equipment (UE) to estimate the downlink radio channel quality, perform path loss calculations, and make decisions related to cell selection, handover, and link adaptation. RSAP was introduced in Release 13 as part of the enhancements for LTE-Advanced and has been carried forward in subsequent releases, with specifications in 3GPP TS 36.509 (Special conformance testing functions) and TS 36.978 (Reference Signal Antenna Power). The parameter is particularly relevant for multi-antenna transmission schemes, where accurate knowledge of per-antenna reference signal power is essential for coherent demodulation and channel state information (CSI) reporting.
In LTE, reference signals (RS) such as Cell-specific Reference Signals (CRS) and Channel State Information Reference Signals (CSI-RS) are transmitted with a known power level relative to the overall cell transmit power. RSAP defines the ratio of reference signal power to the total cell power, or the absolute power per resource element (RE) for reference signals. The UE uses this information to estimate the downlink path loss by comparing the received reference signal power (RSRP) with the known transmitted power. This path loss estimate is then used for uplink power control, so that the UE can set its transmit power appropriately to maintain link quality while minimizing interference. RSAP is also used in the calculation of the channel quality indicator (CQI) and other CSI parameters, which are fed back to the base station for scheduling and link adaptation.
With the introduction of multiple antenna techniques such as MIMO and beamforming, the concept of RSAP has evolved to support per-antenna port power control. In LTE-Advanced and 5G NR, reference signals can be transmitted on multiple antenna ports, each with its own power level. RSAP allows the network to signal the power offset between different antenna ports, enabling the UE to accurately estimate the channel for each port and perform coherent demodulation. This is especially important for transmission modes that use spatial multiplexing or transmit diversity, where the received signal is a combination of signals from multiple antennas.
In 5G NR, the reference signals include Demodulation Reference Signals (DMRS), CSI-RS, and Sounding Reference Signals (SRS). The power of these reference signals is configured by the network through RRC signaling, and RSAP-like parameters are used to indicate the power offset between the reference signal and the data channel. The UE uses these parameters to estimate the channel and perform demodulation. The 3GPP specifications define the signaling of these power parameters and the conformance testing procedures to ensure that UEs correctly interpret and use them.
RSAP is also relevant for network planning and optimization. By setting appropriate RSAP values, operators can balance coverage and capacity, ensure accurate path loss estimation, and avoid excessive interference. The parameter is typically configured during cell setup and can be adjusted based on drive tests and performance measurements. In summary, RSAP is a fundamental physical layer parameter that enables accurate channel estimation, power control, and link adaptation in multi-antenna cellular networks.
Purpose & Motivation
RSAP exists to provide UEs with the necessary information about the transmit power of reference signals, enabling accurate path loss estimation and channel state estimation. Without this information, the UE would not be able to correctly set its uplink transmit power or report accurate CSI, leading to degraded link performance and increased interference. The parameter is particularly important in multi-antenna systems, where per-antenna power differences must be signaled to support coherent demodulation and spatial processing. RSAP was introduced in Release 13 to address the needs of LTE-Advanced and has been maintained in later releases to support 5G NR. It solves the problem of power ambiguity in reference signal transmission, ensuring that UEs can reliably estimate the radio channel and maintain robust communication.
What changed in its specifications
The latest release-to-release comparison of specifications that define RSAP. Each summary describes the whole specification, not only this term.
Added UE test loop mode F for counting received MBMS packets on SC-MTCH in SC-PTM. Added handling of stored MBS positioning information reset and new positioning technology identifiers.
Full comparison in TS 36.509 →Release Timeline
Evolution Across Releases
An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.
Defining Specifications
3GPP specifications that define or reference RSAP, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 36.509 vi00 | UE Conformance Test Loop Functions | Rel-18 read |
| TS 36.978 vd20 | LTE MIMO OTA Antenna Test Function | Rel-13 read |