Description
The Adaptive Multi-Rate (AMR) codec is a family of speech coding algorithms designed for mobile communication systems. It operates by compressing digitized speech signals into a range of bit rates, from 4.75 kbps to 12.2 kbps for narrowband AMR, and 6.60 kbps to 23.85 kbps for AMR-Wideband (AMR-WB). The core principle is source-controlled rate adaptation, where the codec mode (bit rate) is selected based on real-time assessments of radio channel quality and network load. This selection is managed by the network through in-band signaling or explicit control messages, allowing the system to prioritize either voice quality or capacity as needed.
Architecturally, AMR integrates into the voice processing chain at the User Equipment (UE) and the core network's Media Gateway (MGW) or Media Resource Function (MRF). The codec employs Algebraic Code-Excited Linear Prediction (ACELP) for narrowband and a modified ACELP for wideband, providing efficient modeling of the vocal tract and excitation signal. Key components include the speech encoder/decoder (codec), a Voice Activity Detector (VAD) for discontinuous transmission (DTX), and a comfort noise generator (CNG) to mask transmission gaps. The codec operates in conjunction with channel coding and interleaving in the physical layer to ensure robustness against errors.
In the network, AMR plays a pivotal role in the voice bearer path. For circuit-switched voice in GSM and UMTS, it is applied directly over the air interface, with the TRAU (Transcoder and Rate Adaptation Unit) or MGW handling rate adaptation and transcoding to/from PSTN codecs like G.711. For Voice over LTE (VoLTE) and Voice over NR (VoNR), AMR-WB is used as the primary codec within the IP Multimedia Subsystem (IMS), encapsulated in RTP/UDP/IP packets. The codec's adaptability allows the Radio Access Network (RAN) to command a lower bit rate during poor radio conditions, increasing channel coding protection and maintaining call continuity, or a higher bit rate for superior quality in good conditions.
The evolution to AMR-WB (marketed as HD Voice) extended the audio bandwidth from 300–3400 Hz to 50–7000 Hz, significantly improving naturalness and intelligibility. This required updates throughout the voice chain, including acoustic components in devices and wider bandwidth support in networks. AMR's design also facilitates seamless handovers between different radio access technologies (e.g., GSM to UMTS) through codec mode renegotiation and transcoding in the core network. Its standardized frame structure and control mechanisms ensure interoperability across vendors and operators, making it a foundational technology for global mobile voice services.
Purpose & Motivation
AMR was created to address the limitations of fixed-rate speech codecs used in early digital mobile systems like GSM, which employed the Full-Rate (FR) and Half-Rate (HR) codecs. These fixed codecs could not adapt to varying radio conditions: the FR codec provided consistent but sometimes inadequate quality under interference, while the HR codec offered higher capacity but lower quality. The primary motivation was to optimize the trade-off between voice quality and spectral efficiency dynamically, allowing networks to maintain acceptable quality during congestion or poor coverage while maximizing capacity during ideal conditions.
Historically, the introduction of AMR in 3GPP Release 99 (for GSM) and its adoption for UMTS was driven by the need for a unified, robust voice codec that could leverage advancements in digital signal processing. It solved the problem of inefficient spectrum usage by enabling the network to command a lower bit rate (and thus stronger error protection) during cell edge or interference scenarios, reducing drop calls. Conversely, in clear conditions, it could use higher bit rates for near-toll-quality audio. This adaptability was crucial for supporting higher user densities and improving overall service reliability.
Furthermore, AMR provided a migration path for enhanced voice services. It laid the groundwork for wideband audio (AMR-WB), which addressed the growing demand for high-definition voice experiences as networks evolved to packet-switched IMS architectures in LTE and 5G. By standardizing a single, adaptable codec family, 3GPP ensured backward compatibility and smooth interworking between legacy and modern networks, reducing complexity for operators and enabling consistent voice quality across generations.
What changed in its specifications
The latest release-to-release comparison of specifications that define AMR. Each summary describes the whole specification, not only this term.
Rel-18 brings only minor changes to TS 21.905: 0 clauses changed, with no change attributed to a release feature.
Full comparison in TR 21.905 →Rel-19 brings only minor changes to TS 23.107: 0 clauses changed, with no change attributed to a release feature.
Full comparison in TS 23.107 →Technology family
Speech and voice codecs · Services › Codecs
Members and relations were proposed independently by several models and kept only where at least two agree; quotes are verified verbatim against the specifications. Release = first approved version of the defining specification.
Release Timeline
Detected Changes Across Releases
verified against 3GPP sourcesDocumented changes in 15 releases, each verified against the text of 3GPP specifications or approved change requests and shown with the exact wording. The release timeline above shows the same releases. A release without an entry has no documented change for this term.
Introduced in R98 (release dating of the term; no individual change cited).
TS 26.102 v340 first specifies the mapping of AMR generic frames to the Iu and Uu interfaces, including RAB parameters and the RFCS/PDU type 0 handling for AMR speech.
- “The present document specifies the mapping of the AMR generic frame format (3GPP TS 26.101) to the Iu Interface (3GPP TS 25.415) and the Uu Interface.” TS 26.102 v3.4.0
- “The AMR RAB is established with one or more RAB co-ordinated sub-flows with predefined sizes and QoS parameters.” TS 26.102 v3.4.0
Rel-4 extends AMR frame mapping to the Nb interface (TrFO/MGW, PDU Type 0 with CRC) and adds AMR-specific TFO specification (TS 28.062) with codec compatibility rules.
- “the Uu Interface and the Nb Interface (3GPP TS 29.415)” TS 26.102 v4.1.0
- “PDU Type 0 (with payload CRC) shall be used for the transport of AMR coded speech on the Nb interface” TS 26.102 v4.1.0
- “All members of the AMR Codec Type family, except UMTS_AMR, are compatible, when both Codec Types use compatible multi-mode ACSs.” TS 28.062 v4.6.0
Rel-5 extends AMR handling in TFO: adds AMR-NB/AMR-WB codec type families, OHR_AMR, compatibility rules between UMTS_AMR and UMTS_AMR_2, and step-by-step codec mode adaptation guidance.
- “In any multi-mode configuration the UMTS_AMR shall be regarded as only compatible to itself, not to any other AMR-NB Codec Type” TS 28.062 v5.5.0
- “the used mode should be changed in a step-by-step fashion within the configured set of codec modes” TS 26.102 v5.2.0
- TFO/TrFO compatibility of UMTS_AMR and UMTS_AMR2 TS 23.153CR076
TS 28.062 changed the AMR TFO frame format selection, so AMR_TFO_8+8k applies only when HR_AMR lacks the 7.95 kbit/s mode. TS 26.102 extended the AMR Nb mapping to cover GSM_EFR.
- “For any TFO connection with at least one side using the HR_AMR with a configuration not including the mode 7.95 kBit/s the TFO frame format shall be AMR_TFO_8+8k” TS 28.062 v6.4.0
- “For all other AMR TFO connections, including HR_AMR with 7.95 kBit/s in the ACSes on both sides, the TFO Frame format shall be AMR_TFO_16k” TS 28.062 v6.4.0
- “it shall be assumed that AMR mode 12.2 kbps is (of course) not included” TS 28.062 v6.4.0
PCM coded speech mapping on the Nb Interface is now specified separately for 5ms frames (Table 8-1) and 20ms frames (Table 8-2), instead of a single mapping.
- “the mapping for the PCM coded speech in 5ms frames on the Nb Interface shall be as defined in Table 8-1” TS 26.102 v7.1.0
- “the mapping for the PCM coded speech in 20ms frames on the Nb Interface shall be as defined in Table 8-2” TS 26.102 v7.1.0
MTSI specification 26.114 added requirements on AMR and AMR-WB handling in terminals and MTSI MGWs (transcoding avoidance, mode-change restriction, SDP parameters, RTCP APP adaptation), and 26.102 extended AMR/AMR-WB Nb/Iu/A-interface mapping.
- “If the MTSI MGW is performing transcoding of AMR or AMR-WB then it shall be capable of restricting mode changes” TS 26.114 v8.15.0
- “For AMR and AMR-WB encoded media, the MTSI MGW shall support the adaptation signalling method using RTCP APP packets” TS 26.114 v8.15.0
- “Delivery of erroneous SDUs for AMR- and AMR-WB-coded speech, as well as for GSM_FR-, GSM_HR-, GSM_EFR-coded speech” TS 26.102 v8.5.0
In TS 26.114, AMR/AMR-WB adaptation handling changed: CMR in the AMR RTP payload is now mandated and usable for mode adaptation, including ECN-triggered adaptation, and the MGW and initial codec mode rules were revised.
- “RTP CMR is mandated to be supported by any AMR or AMR-WB implementation using the RTP profile [28].” TS 26.114 v9.15.0
- “If ECN-triggered adaptation is used with AVP then the RTCP APP signalling could be too slow” TS 26.114 v9.15.0
- “unless inband CMR is used for rate adaptation. It shall however accept requests signalled with the CMR bits in the AMR payload format.” TS 26.114 v9.15.0
MTSI clients must now set the SDP b=AS bandwidth for AMR and AMR-WB according to mode-set, ptime and redundancy, with new b=AS tables and a computation annex.
- “the MTSI client shall set the b=AS parameter to a value matching the maximum codec mode in the mode-set, the packetization time (ptime)” TS 26.114 v10.11.0
- “the MTSI client shall set the b=AS parameter in the SDP to a value matching the highest AMR/AMR-WB mode” TS 26.114 v10.11.0
The recommended AMR mode subset rationale in the MTSI guidelines changed from transport-layer optimization to GERAN/UTRAN usage and bit-rate granularity, and AMR RAB sub-flow mapping became subject to operator tuning.
- “the set includes codec modes frequently used in GERAN and UTRAN, and enables to control quality and capacity with appropriate bit-rate granularity.” TS 26.114 v11.12.0
- “For AMR, subject to operator tuning, the first RAB sub-flow (sub-flow 1) corresponds with the Class A bits.” TS 26.102 v11.0.0
TS 26.114 changed AMR handling in MTSI: added an AMR codec requirements clause (5.2.1.2) and MGW AMR support, and updated b=AS SDP bandwidth rules to cover AMR alongside EVS.
- “5.2.1.2 Detailed codec requirements, AMR” TS 26.114 v12.17.0
- “MTSI MGWs offering speech communication between an MTSI client in a terminal and a client in another IP network” TS 26.114 v12.17.0
- “the MTSI client shall set the b=AS parameter in the SDP to a value matching the highest AMR/AMR-WB mode” TS 26.114 v12.17.0
TS 26.114 changes how AMR is used in MTSI: session setup now determines bandwidth, a=bw-info bandwidth properties are recommended for AMR modes, and CMR handling rules are reworded.
- “For AMR or AMR-WB encoded media, the session setup shall determine the applicable bandwidth(s) as defined in clause 6.2.5” TS 26.114 v13.11.0
- “Recommended bandwidth properties for AMR to be used with the ‘a=bw-info’ attribute when codec modes up to 12.2 are negotiated” TS 26.114 v13.11.0
- “the MTSI client shall accept that the remote party sends with lower modes within the negotiated mode-set than requested by the CMR” TS 26.114 v13.11.0
TS 26.114 Rel-14 adds SDP ccc_list signalling examples for codec capability negotiation that include AMR alongside EVS and AMR-WB, with encoder/decoder capability parameters.
- “a = ccc_list:EVS;AMR-WB;AMR|ENC:1;1;1:DEC:3,1,1|ENC:1;1;0:DEC:4,1,0|ENC:1;0;1:DEC:5,0,0” TS 26.114 v14.12.0
- “The MTSI client in terminal shall be capable of operating with any subset of these 8 codec modes.” TS 26.114 v14.12.0
AMR specifications were corrected in Rel-16: 26.104 got corrections to the AMR floating-point code, and 26.114 added Table W.3.1 with code points for AMR.
- Corrections to AMR Floating-Point Code TS 26.104CR0035
- “Table W.3.1: Code points for AMR” TS 26.114 v16.13.0
Defining Specifications
3GPP specifications that define or reference AMR, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TR 21.905 vj20 | 3GPP Terminology and Definitions | Rel-19 read |
| TS 22.495 v700 | NGN Requirements for IMS Services | Rel-7 read |
| TS 22.813 va00 | Enhanced Voice Services for EPS | Rel-10 read |
| TR 22.977 vj00 | Speech Enabled Services and Multimodal Framework | Rel-19 read |
| TS 23.107 vj00 | UMTS QoS Framework | Rel-19 read |
| TS 23.207 vj00 | End-to-End QoS Framework for GPRS | Rel-19 read |
| TS 23.228 vk10 | IP Multimedia Core Network Subsystem | Rel-20 read |
| TS 23.333 vj00 | MRFC-MRFP Mp Interface Requirements | Rel-19 read |
| TS 23.334 vj00 | IMS-ALG to IMS-AGW Interface (Iq) Stage 2 | Rel-19 read |
| TS 23.802 v700 | Enhanced End-to-End QoS Architecture | Rel-7 read |
| TR 23.979 vj00 | PoC over 3GPP Systems Architectural Requirements | Rel-19 read |
| TS 24.147 vj00 | IMS Conferencing Protocol Details | Rel-19 read |
| TS 24.819 v700 | IMS Services via Fixed Broadband Access | Rel-7 read |
| TR 24.930 vj00 | IMS Session Setup Signalling Flows | Rel-19 read |
| TS 25.323 vj00 | Packet Data Convergence Protocol (PDCP) Specification | Rel-19 read |
| TS 25.415 vj00 | Iu Interface User Plane Protocol | Rel-19 read |
| TS 26.071 vj00 | AMR Speech Codec Introduction | Rel-19 read |
| TS 26.077 vj00 | AMR Noise Suppression Minimum Performance Requirements | Rel-19 read |
| TS 26.090 vj00 | AMR Speech Codec Detailed Mapping Specification | Rel-19 read |
| TS 26.092 vj00 | AMR Comfort Noise for SCR Operation | Rel-19 read |
| TS 26.102 vj00 | Mapping of AMR and other codecs to interfaces | Rel-19 read |
| TS 26.111 vj00 | 3G-324M Terminal Specification for CS Multimedia | Rel-19 read |
| TS 26.114 vk11 | IMS Multimedia Telephony Client | Rel-20 read |
| TS 26.117 vj20 | 5G Media Streaming (5GMS) | Rel-19 read |
| TS 26.131 vj00 | Terminal Acoustic Performance Requirements | Rel-19 read |
| TS 26.132 vk00 | Terminal Acoustic Test Methods for Telephony | Rel-20 read |
| TS 26.141 vj00 | IMS Messaging & Presence Media Formats | Rel-19 read |
| TS 26.143 vj10 | Messaging Media Profiles | Rel-19 read |
| TS 26.171 vj00 | Introduction to AMR-WB Speech Processing | Rel-19 read |
| TS 26.177 vj00 | DSR Extended Advanced Front-end Test Sequences | Rel-19 read |
| TS 26.190 vj00 | AMR-WB Speech Codec Detailed Mapping | Rel-19 read |
| TS 26.192 vj00 | AMR-WB Comfort Noise Requirements | Rel-19 read |
| TS 26.202 vj00 | AMR-WB Speech Codec Mapping Specification | Rel-19 read |
| TS 26.231 vj00 | CTM Minimum Performance Requirements Testing | Rel-19 read |
| TS 26.235 vc00 | Default Codecs for 3GPP IP Multimedia Subsystem | Rel-12 read |
| TS 26.236 vc00 | Packet Switched Conversational Multimedia Protocols | Rel-12 read |
| TS 26.244 vj10 | 3GPP File Format (3GP) Specification | Rel-19 read |
| TS 26.256 vj10 | IVAS Jitter Buffer Management Specification | Rel-19 read |
| TS 26.267 vj00 | eCall In-band Modem Specification | Rel-19 read |
| TS 26.269 vj00 | eCall In-band Modem Conformance Testing | Rel-19 read |
| TS 26.274 vj00 | AMR-WB+ Codec Conformance Testing Specification | Rel-19 read |
| TS 26.290 vj00 | AMR-WB+ Audio Codec Specification | Rel-19 read |
| TS 26.447 vj00 | EVS Frame Loss Concealment Procedure | Rel-19 read |
| TS 26.448 vj00 | EVS Jitter Buffer Management Specification | Rel-19 read |
| TS 26.511 vj00 | 5G Media Streaming Profiles, Codecs & Formats | Rel-19 read |
| TR 26.916 ve20 | eSRVCC Transcoding Minimization Study | Rel-14 read |
| TR 26.923 vj00 | Study on IMS-based Telepresence Media Handling | Rel-19 read |
| TR 26.926 vj00 | Traffic Models & Quality Evaluation for Media/XR in 5G | Rel-19 read |
| TR 26.937 vj00 | 3GPP PSS Characterization | Rel-19 read |
| TR 26.943 vj00 | SES Codec Selection Report | Rel-19 read |
| TR 26.952 vj00 | EVS Codec Selection, Verification & Characterization | Rel-19 read |
| TR 26.967 vj00 | eCall via CTM Suitability Analysis | Rel-19 read |
| TR 26.969 vj00 | eCall In-band Modem Performance Characterization | Rel-19 read |
| TR 26.975 vj00 | AMR Speech Codec Performance Background | Rel-19 read |
| TR 26.976 vj00 | AMR-WB Codec Characterization & Verification | Rel-19 read |
| TR 26.978 vj00 | AMR Noise Suppression Selection Phase Technical Report | Rel-19 read |
| TS 28.062 vj00 | Tandem Free Operation (TFO) Service Description | Rel-19 read |
| TS 29.163 vj00 | Interworking between 3GPP IM CN and CS networks | Rel-19 read |
| TS 29.332 vj00 | MGCF-IM-MGW Interface Protocol (Mn) | Rel-19 read |
| TS 36.750 ve10 | Study on enhancement of VoLTE | Rel-14 read |
| TS 43.068 vj00 | Voice Group Call Service (VGCS) Stage 2 | Rel-19 read |
| TS 43.069 vj00 | Voice Broadcast Service (VBS) Stage 2 | Rel-19 read |
| TS 45.009 vj00 | GSM AMR Link Adaptation & Control | Rel-19 read |
| TR 45.903 vj00 | SAIC Feasibility Study for GSM Networks | Rel-19 read |
| TR 45.912 vj00 | GERAN Evolution Feasibility Study | Rel-19 read |
| TR 45.913 vj00 | Optimized Transmit Pulse Shape for EGPRS2-B | Rel-19 read |
| TR 45.914 vj00 | MUROS Feasibility Study for Voice Capacity | Rel-19 read |
| TS 48.061 vj00 | BTS-TRAU Protocol for HR Speech/Data | Rel-19 read |
| TR 26.935 vj00 | Speech Codec Performance for Packet Switched Multimedia | Rel-19 read |