Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Radio Access Network

EGPRS

Enhanced GPRS

Radio Access Network →

EGPRS is an enhancement to the GPRS packet-switched data service in GSM/EDGE networks that uses advanced modulation and coding schemes to significantly increase data rates and spectral efficiency.

Introduced
R99
Where
Radio Access Network
Specifications
15 specs
Also in
Services
EGPRS Description Purpose What changed Family Neighbours Detected Changes Specifications

Description

Enhanced GPRS (EGPRS), commonly marketed as EDGE (Enhanced Data rates for GSM Evolution), is a pivotal upgrade to the GSM radio access network that dramatically improved its packet-switched data capabilities. It is defined as an evolution of the GPRS (General Packet Radio Service) standard, introducing new modulation techniques and more flexible link adaptation mechanisms to the existing TDMA (Time Division Multiple Access) frame structure of GSM.

At its core, EGPRS retains the 200 kHz carrier bandwidth and TDMA frame structure of GSM but replaces the Gaussian Minimum Shift Keying (GMSK) modulation used by GPRS with a more spectrally efficient 8-Phase Shift Keying (8PSK) modulation. This allows 3 bits to be transmitted per symbol instead of 1, tripling the raw symbol rate. Combined with this, EGPRS introduced nine Modulation and Coding Schemes (MCS-1 through MCS-9), which blend GMSK and 8PSK modulation with varying levels of forward error correction coding. The network and mobile station dynamically select the optimal MCS based on real-time radio channel conditions (a process called link adaptation), switching between GMSK and 8PSK and adjusting the code rate to maximize throughput or reliability.

Architecturally, EGPRS integrates seamlessly into the existing GSM/GPRS network. It requires upgrades at the BTS (Base Transceiver Station) and BSC (Base Station Controller) to support the new modulation and the more complex signal processing, as well as new terminal hardware. The core network (SGSN, GGSN) remains largely unchanged, treating EGPRS as a higher-speed access bearer. Key operational features include Incremental Redundancy (also called Hybrid ARQ Type II), where initially sent data packets contain high-coding-rate data, and if decoding fails, additional parity bits are sent in subsequent transmissions and combined with the original for a more robust decode, improving efficiency over poor links.

Purpose & Motivation

EGPRS was developed to address the severe bandwidth limitations of the original GPRS technology, which offered theoretical maximum data rates of only about 115 kbps but often delivered much lower practical speeds. As internet usage grew in the early 2000s, the demand for faster mobile data on the ubiquitous GSM network infrastructure skyrocketed. Deploying entirely new 3G UMTS networks was costly and time-consuming, creating a pressing need for a significant evolutionary upgrade to the existing GSM spectrum and hardware.

EGPRS solved this by providing a 'bolt-on' enhancement that could triple the data throughput within the same 200 kHz radio channel, effectively boosting spectral efficiency. It addressed the limitations of GPRS's fixed coding schemes and single modulation type by introducing adaptive modulation and coding, allowing the system to thrive in both excellent and poor radio conditions. This made efficient use of the scarce spectrum resource and extended the commercial life of GSM networks by enabling them to offer competitive '2.75G' data services, such as mobile email and basic web browsing, years before 3G coverage became widespread.

Its introduction, beginning in 3GPP Release 99, provided a clear and cost-effective migration path for operators. It allowed them to offer enhanced data services while protecting their existing infrastructure investments, bridging the gap between basic GPRS and the high-speed packet access of UMTS/HSPA, and meeting the growing consumer demand for mobile internet access.

What changed in its specifications

The latest release-to-release comparison of specifications that define EGPRS. Each summary describes the whole specification, not only this term.

TR 21.905Rel-17 → Rel-18

Rel-18 brings only minor changes to TS 21.905: 0 clauses changed, with no change attributed to a release feature.

Full comparison in TR 21.905 →
TS 22.060Rel-18 → Rel-19

Rel-19 brings only minor changes to TS 22.060: 0 clauses changed, with no change attributed to a release feature.

Full comparison in TS 22.060 →

Technology family

Radio access technologies · Radio Access Network

  1. Phase 1 GSM
  2. R97 GPRS
  3. R99 EDGE, EGPRS, UTRA, UTRA-FDD, UTRA-TDD, UTRA-WTDD
  4. Rel-4 GERAN, UTRA-NTDD
  5. Rel-7 EGPRS2
  6. Rel-8 E-UTRA
  7. Rel-13 EC-GSM-IoT, LTE-M, NB-IoT
  8. Rel-15 NR
  9. Rel-17 NR RedCap
  10. Rel-18 NR eRedCap
  • EGPRS extended by EC-GSM-IoT
    “EC-GSM-IoT is an evolution of EGPRS providing a streamlined protocol implementation” TS 43.064
  • EGPRS builds on GPRS
    “Introduction of Enhanced GPRS (EGPRS)” TS 43.064
  • EGPRS extended by EGPRS2
    “EGPRS2 Enhanced GPRS phase 2” TS 43.064

Members and relations were proposed independently by several models and kept only where at least two agree; quotes are verified verbatim against the specifications. Release = first approved version of the defining specification.

Release Timeline

Detected Changes Across Releases

verified against 3GPP sources

Documented changes in 12 releases, each verified against the text of 3GPP specifications or approved change requests and shown with the exact wording. The release timeline above shows the same releases. A release without an entry has no documented change for this term.

R99 introduced

Introduced in R99 (release dating of the term; no individual change cited).

Rel-4 specification text

EGPRS is specified for the first time in these specifications: 8PSK and MCS-1 to MCS-9 coding schemes, Incremental Redundancy, an EGPRS TBF mode, EGPRS mobile stations and EGPRS link quality measurements.

  • “Enhanced GPRS (EGPRS): enables higher data rates through usage of 8PSK modulation in addition to GMSK EGPRS also enables Incremental Redundancy operation.” TS 44.060 v4.23.0
  • “Nine modulation and coding schemes, MCS-1 to MCS-9, are defined for the EGPRS packet data traffic channels.” TS 43.064 v4.5.0
  • “A TBF may operate in either GPRS or EGPRS TBF mode.” TS 44.060 v4.23.0
Rel-6 specification text

EGPRS TBF mode handling changed: the network may now set the TBF mode in additional multiple-TBF assignment messages, and EGPRS-specific procedures, such as T3190 restart on erroneous RLC blocks, were specified.

  • “The network sets the TBF mode in the PACKET UPLINK ASSIGNMENT, MULTIPLE TBF UPLINK ASSIGNMENT, PACKET DOWNLINK ASSIGNMENT” TS 44.060 v6.28.0
  • “In EGPRS TBF mode T3190 is also restarted when receiving an erroneous RLC data block for which the header is correctly received” TS 44.060 v6.28.0
  • “A mobile station supporting EGPRS shall support RLC buffers as defined in the table below” TS 44.060 v6.28.0
Rel-7 specification text

Rel-7 extends EGPRS with EGPRS2 (higher symbol rate, turbo codes, QPSK/16-QAM/32-QAM), adds FANR and Reduced Latency, and changes TBF mode definitions and EGPRS quality reporting.

  • “Enhanced GPRS Phase 2 enables higher data rates through usage of higher symbol rate, turbo codes, and QPSK, 16-QAM and 32-QAM modulations” TS 44.060 v7.27.0
  • “An EGPRS mobile station may additionally indicate support for EGPRS2 in uplink and/or downlink direction.” TS 43.064 v7.13.0
  • “Correction to MEAN_BEP and CV_BEP calculations when new timeslot configuration is allocated during a downlink EGPRS TBF” TS 45.008 v7.21.0
Rel-8 specification text

TS 44.060 Rel-8 revised EGPRS RLC/MAC procedures, including PAN polling behaviour, and carried CRs for EGPRS level change correction and alignment on multiplexing GPRS, EGPRS and EGPRS2.

  • “EGPRS Level Change Correction” TS 44.060 v8.17.0
  • “Release 8 alignment on Multiplexing GPRS,EGPRS,EGPRS2” TS 44.060 v8.17.0
  • “does not have any TBF assigned in the uplink direction or does not have an uplink TBF that has been assigned a PDCH” TS 44.060 v8.17.0
Rel-9 specification text

In Rel-9, EMST was added for EGPRS TBF mode, requiring EMST-capable mobile stations and networks to support EGPRS and changing EGPRS downlink ACK/NACK and TBF release handling per RLC entity.

  • “EMST is applicable only to TBFs in EGPRS TBF mode.” TS 44.060 v9.14.0
  • “A mobile station and a network that support EMST shall also support EGPRS.” TS 44.060 v9.14.0
  • “If EMST is used and the mobile station responds to the poll with a (EGPRS) PACKET DOWNLINK ACK/NACK message” TS 44.060 v9.14.0
Rel-10 specification text

EGPRS behaviour changed: Dynamic Timeslot Reduction and EMSR are specified for EGPRS TBF mode, FANR PAN insertion rules were refined, and EGPRS2 link quality reporting modulation selection was altered.

  • “Dynamic Timeslot Reduction (DTR) is a feature used by the network to reduce the number of downlink timeslots monitored by the mobile station” TS 44.060 v10.13.0
  • “EMSR may only be used on a TBF operating in EGPRS TBF mode.” TS 44.060 v10.13.0
  • “In case of EGPRS2 downlink the MS shall report the MEAN_BEP and CV_BEP for up to two modulations schemes” TS 45.008 v10.7.0
Rel-11 specification text

EGPRS TBF mode and signalling changed: TBFs in IMMEDIATE PACKET ASSIGNMENT must use EGPRS mode, and a new EGPRS PACKET DOWNLINK ACK/NACK TYPE 3 message is added with its support indication.

  • “A TBF assigned in IMMEDIATE PACKET ASSIGNMENT message shall operate in EGPRS TBF mode.” TS 44.060 v11.9.0
  • “The mobile station shall not send an EGPRS PACKET DOWNLINK ACK/NACK TYPE 3 message if not indicated as supported by the network” TS 44.060 v11.9.0
Rel-12 specification text

EGPRS TBF mode and EGPRS Packet Downlink Ack/Nack signalling were extended to Downlink Multi Carrier (DLMC), with a new EGPRS PACKET DOWNLINK ACK/NACK DLMC message and mandatory EGPRS TBF mode for DLMC.

  • “For Downlink Dual Carrier and DLMC configurations TBFs shall operate in EGPRS TBF mode.” TS 44.060 v12.6.0
  • “it shall be coded using CS-1 or CS-3 as indicated by the most recently received assignment message.” TS 44.060 v12.6.0
  • “the assignment of only one EGPRS TBF on the downlink where multiple PDCHs may be assigned on two or more different radio frequency channels.” TS 44.060 v12.6.0
Rel-13 specification text

EGPRS TBF mode, MCS use, IR and measurement/reporting procedures were extended in Rel-13 to cover EC-GSM-IoT/EC TBF mode, which reuses EGPRS modulation and coding schemes.

  • “The EC TBF uses the EGPRS Modulation and Coding Schemes with GMSK modulation (MCS-1 to MCS-4) and optionally, with 8-PSK modulation (MCS-5 to MCS-9).” TS 44.060 v13.6.0
  • “In EC operation the only level supported is EGPRS.” TS 44.060 v13.6.0
  • “In case of EGPRS or EC-GSM-IoT the MS shall report the overall MEAN_BEP and CV_BEP” TS 45.008 v13.12.0
Rel-14 specification text

EGPRS RLC/MAC procedures in TS 44.060 were extended: new EGPRS MULTILATERATION REQUEST message contents were added, and EGPRS downlink Ack/Nack messages now carry MS Transmission Offset and MS Sync Accuracy parameters.

  • “EGPRS Packet Downlink Ack/Nack Type 2 and EGPRS Packet Downlink Ack/Nack Type 3 messages shall include these parameters” TS 44.060 v14.2.0
  • “< EGPRS MULTILATERATION REQUEST message content >” TS 44.060 v14.2.0
  • “Table 11.2.5a.4: EGPRS PACKET CHANNEL REQUEST message and EGPRS MULTILATERATION REQUEST message content (PEO access)” TS 44.060 v14.2.0
Rel-16 1 CR

Channel quality report derivation during EGPRS downlink TBF transfer (with EC-GSM-IoT) was corrected in TS 45.008.

  • Correction on channel quality report derivation during EGPRS and EC-GSM-IoT downlink TBF transfer TS 45.008CR0685

Defining Specifications

3GPP specifications that define or reference EGPRS, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TR 21.905 vj20 3GPP Terminology and Definitions Rel-19 read
TS 22.060 vj00 GPRS Stage 1 Service Description Rel-19 read
TS 23.060 vj00 GPRS Stage 2 Service Description Rel-19 read
TS 23.228 vk10 IP Multimedia Core Network Subsystem Rel-20 read
TR 26.936 vj00 Audio Codec Characterization Technical Report Rel-19 read
TR 26.937 vj00 3GPP PSS Characterization Rel-19 read
TS 31.111 vj40 3GPP TS 31111 vj40: USIM Application Toolkit Rel-19 read
TS 43.051 vj00 GERAN Stage 2 Service Description Rel-19 read
TS 43.064 vj00 GPRS Radio Interface Lower-Layer Functions Rel-19 read
TS 44.060 vj00 GERAN RLC/MAC Protocol Specification Rel-19 read
TS 44.160 vg00 GERAN Iu Mode RLC/MAC Protocol Specification Rel-16 read
TR 45.912 vj00 GERAN Evolution Feasibility Study Rel-19 read
TR 45.914 vj00 MUROS Feasibility Study for Voice Capacity Rel-19 read
TR 45.926 vj00 GERAN BTS Energy Saving Study Rel-19 read
TS 51.021 vj00 RF test methods and conformance requirements for GSM BSS Rel-19 read