Description
The Higher Edge is a frequency reference point defined in 3GPP TS 36.104 (base station radio transmission and reception), TS 36.141 (base station conformance testing), and TS 36.808 (carrier aggregation base station conformance testing). It denotes the highest frequency of a channel bandwidth in a given operating band. Depending on the configuration, it can refer to three different things: the highest frequency in the aggregated channel bandwidth for multiple contiguously aggregated carriers in a specified operating band; the highest frequency in the channel bandwidth of a single E-UTRA carrier; or the highest frequency in the channel bandwidth of the highest carrier for E-UTRA multi-carrier operation in a specified operating band.
The concept is needed because RF requirements such as spectrum emission mask, adjacent channel leakage ratio (ACLR), spurious emissions, and blocking are defined relative to the edges of the channel bandwidth. For a single carrier, the channel bandwidth has a lower edge and a higher edge, and the requirement is evaluated at and beyond the higher edge. For contiguous carrier aggregation, the aggregated channel bandwidth is treated as a single wide channel, and the higher edge is the highest frequency of the aggregated block. For multi-carrier operation with non-contiguous carriers, the higher edge is the highest frequency of the highest carrier.
The Higher Edge is used together with its counterpart, the Lower Edge, to define the frequency boundaries of the transmitted signal. Transmitter requirements such as the operating band unwanted emissions and the spectrum emission mask are specified as a function of the frequency offset from the edge, and receiver requirements such as adjacent channel selectivity and blocking are defined relative to the edge. By defining a single reference point, the specifications can write requirements that apply uniformly to single-carrier, contiguous aggregation, and multi-carrier configurations.
The definition was introduced in Rel-10, which is when carrier aggregation was first specified in LTE. Rel-10 introduced the concept of the aggregated channel bandwidth and the need for a common frequency reference for the aggregated signal. The term was defined once and has not been revised since, because the underlying concept is stable: the higher edge is simply the highest frequency of the relevant channel or aggregated channel. The definition remains in Rel-10 of the specifications and is referenced by later releases through the specification versioning process.
For engineers, the Higher Edge is a practical tool for computing test frequencies and for understanding where emission limits apply. For example, when testing a base station's spectrum emission mask, the measurement frequencies are expressed as offsets from the Higher Edge (and Lower Edge) of the carrier or aggregated carriers. Similarly, when planning a deployment, the Higher Edge determines the boundary beyond which the operator must control emissions into adjacent spectrum.
Purpose & Motivation
The Higher Edge exists to provide a single, unambiguous frequency reference for RF requirements in LTE base stations. Before carrier aggregation, requirements could be defined relative to the edge of a single carrier's channel bandwidth. With the introduction of carrier aggregation in Rel-10, the transmitted signal could consist of multiple contiguous carriers forming a wider aggregated channel, or multiple non-contiguous carriers. The specifications needed a way to define the upper frequency boundary of the transmitted signal in all these cases so that emission and blocking requirements could be evaluated consistently.
The term solves the problem of applying requirements to different bandwidth configurations without redefining the requirements for each configuration. By defining the Higher Edge as the highest frequency of the relevant channel or aggregated channel, the specifications can express requirements as offsets from that edge, and the same requirement text applies whether the base station is transmitting a single 20 MHz carrier, two contiguous 20 MHz carriers, or multiple carriers in different bands. This reduces specification complexity and ensures consistent testing.
The definition was introduced in Rel-10 alongside the carrier aggregation work in LTE. It has not needed revision because it is a geometric definition based on frequency boundaries, which do not change as new features are added. The concept is analogous to the Lower Edge, and together they form the frequency reference framework for RF conformance testing.
What changed in its specifications
The latest release-to-release comparison of specifications that define Higher Edge. Each summary describes the whole specification, not only this term.
Rel-18 adds NR bands n54, n105, n106 and n109 to the BS emission and spurious and blocking requirements in TS 36.104. These entries cover wide-area, local and medium-range base stations.
Full comparison in TS 36.104 →Rel-13 added PUCCH format 4 and 5 performance tests, new operating bands, carrier aggregation band combinations, and four new FDD bands in the 2GHz range.
Full comparison in TS 36.141 →Evolution Across Releases
An overview written from the defining specifications, not a verified change history. For the exact text, open the specifications listed below.
Initial definition introduced alongside LTE carrier aggregation: the Higher Edge is the highest frequency in the aggregated channel bandwidth for contiguous carriers, in the channel bandwidth of a single E-UTRA carrier, or in the channel bandwidth of the highest carrier for multi-carrier operation, used as a frequency reference for transmitter and receiver requirements.
Defining Specifications
3GPP specifications that define or reference Higher Edge, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 36.104 vj20 | E-UTRA/NB-IoT Base Station RF Requirements | Rel-19 read |
| TS 36.141 vj10 | RF Test Methods for LTE and NB-IoT Base Stations | Rel-19 read |
| TS 36.808 va10 | LTE Carrier Aggregation BS RF Requirements | Rel-10 read |