Description
CSI-IM (CSI-Interference Measurement) is a critical physical layer mechanism defined in 3GPP specifications for LTE and 5G NR. It is a set of resource elements (REs) within the time-frequency grid that are configured by the network to be empty of desired signal transmission from the serving cell. The User Equipment (UE) measures the power received on these specific REs, which primarily consists of interference and noise from other cells, co-channel users, or other noise sources. This measured interference level is a key input for the UE's Channel State Information (CSI) computation, which includes metrics like Channel Quality Indicator (CQI), Precoding Matrix Indicator (PMI), and Rank Indicator (RI). The architecture for CSI-IM involves the base station (eNB in LTE, gNB in NR) configuring the UE with a CSI-IM resource via higher layer signaling (RRC). This configuration specifies the periodicity, time-domain offset, and frequency-domain location (e.g., specific resource blocks and OFDM symbols) of the CSI-IM resource. The configuration is aligned with the CSI-RS (Channel State Information Reference Signal) resource for the desired signal measurement, allowing the UE to compute CSI based on both signal and interference estimates from coordinated resources. The UE's physical layer then performs the measurement during the configured CSI-IM occasions, typically using techniques like linear minimum mean square error (LMMSE) estimation or simpler power averaging. The measured interference is then used in the CSI calculation algorithm, often involving a lookup table or formula to map the estimated signal-to-interference-plus-noise ratio (SINR) to a recommended CQI value. The final CSI report, which incorporates this interference-aware measurement, is then fed back to the base station via the PUCCH or PUSCH. In the network, the scheduler at the base station uses this CSI report to make intelligent decisions on modulation and coding scheme (MCS), spatial layers (rank), and precoding for downlink transmissions to that UE. By accurately knowing the interference conditions, the scheduler can avoid overly aggressive MCS selections that would lead to high block error rates, or overly conservative ones that waste spectral efficiency. This dynamic adaptation is fundamental to maximizing throughput and reliability, especially in dense deployments, heterogeneous networks (HetNets), and coordinated multipoint (CoMP) scenarios where interference is dynamic and significant. Furthermore, in advanced features like network-assisted interference cancellation and suppression (NAICS), the CSI-IM measurement can help the UE identify specific interfering signals.
Purpose & Motivation
CSI-IM was introduced to address a fundamental limitation in earlier LTE releases (pre-Rel-11) where CSI reporting was primarily based on measuring the desired signal power (via CRS or later CSI-RS) but relied on an implicit or outdated assumption about interference levels. Prior to CSI-IM, interference was often estimated from common reference signals (CRS) which carried both desired and interfering cell signals, making it difficult to isolate the interference component, especially in scenarios with almost blank subframes (ABS) or dynamic point selection. This led to inaccurate CQI reports, causing the base station to select suboptimal modulation and coding schemes, resulting in either wasted capacity (if too conservative) or high retransmission rates (if too aggressive). The creation of CSI-IM was motivated by the need for enhanced interference management in LTE-Advanced networks, particularly for features like enhanced Inter-Cell Interference Coordination (eICIC), further enhanced ICIC (FeICIC), and Coordinated Multipoint (CoMP). These features created dynamic interference patterns that traditional methods could not track accurately. CSI-IM provides a dedicated, configurable resource where the serving cell intentionally mutes its transmission, allowing the UE to obtain a clean measurement of the prevailing interference. This enables more precise link adaptation and scheduling, directly improving spectral efficiency and user experience at the cell edge and in heterogeneous network topologies. Its introduction was a key step towards making cellular networks more robust and efficient in the face of increasing densification and traffic demand.
What changed in its specifications
The latest release-to-release comparison of specifications that define CSI-IM. Each summary describes the whole specification, not only this term.
Rel-19 adds CB-Msg3-EDT procedure support for NTN IoT in TS 36.213, covering new identifiers, MPDCCH/PDSCH/PUSCH handling, and timing and TDD subframe rules. It also adds OCC-related conditions to NPUSCH format 1 transmission, controlled by npusch-OCC-Enabled and the DCI OCC setting.
Full comparison in TS 36.213 →Rel-19 added NTN IoT Phase 3 for LTE, covering regenerative payload S1 removal, Msg3 early data transmission, and ETWS/CMAS for NB-IoT NTN. It also added inter-RAT mobility from E-UTRAN terrestrial network to NR NTN, plus NR NTN feeder link switchover via handover.
Full comparison in TS 36.300 →Technology family
MIMO and beam management · Radio Access Network › NG-RAN (5G)
- R99 Transmit diversity, TSTD
- Rel-7 MIMO
- Rel-8 CSI, DM-RS, MU-MIMO, PMI, RI, SDMA, SRS, SU-MIMO, TPMI
- Rel-10 CSI-RS, NZP CSI-RS
- Rel-11 CoMP, CSI-IM, QCL, UL CLTD, UL MIMO
- Rel-13 CRI, FD-MIMO
- Rel-15 Beam Level Mobility, Beam management, BFD, BFD-RS, BFR, PT-RS, TCI, ZP CSI-RS
- Rel-18 CJT
Also in this family (introduction release not pinned to a single defining specification): Beamforming
- CSI-IM used together with CSI-RS
“Each CSI process defines the CSI measurement associated with one non-zero power CSI-RS resource and one CSI-IM resource.” TS 36.300
Members and relations were proposed independently by several models and kept only where at least two agree; quotes are verified verbatim against the specifications. Release = first approved version of the defining specification.
Release Timeline
Detected Changes Across Releases
verified against 3GPP sourcesDocumented changes in 8 releases, each verified against the text of 3GPP specifications or approved change requests and shown with the exact wording. The release timeline above shows the same releases. A release without an entry has no documented change for this term.
CSI-IM resources are defined for the first time in TS 36.213: TM10 UEs get CSI processes with a CSI-IM resource used to derive interference measurements for CQI.
- “the UE shall derive the interference measurements for computing the CQI value reported in uplink subframe n and corresponding to a CSI process” TS 36.213 v11.13.0
- “the UE can be configured with one or more CSI-IM resource configuration(s)” TS 36.213 v11.13.0
- “7.2.6 Channel-State Information – Interference Measurement (CSI-IM) Resource definition” TS 36.213 v11.13.0
In TS 36.213 Rel-13, CSI-IM resources are associated with CSI processes and CSI-RS resources for eMIMO-Type Class A/B, and CSI-IM is used for interference measurement with restrictions.
- “Each CSI-RS resource is associated with a CSI-IM resource by higher layers.” TS 36.213 v13.16.0
- “based on only the most recent, no later than the CSI reference resource, configured CSI-IM resource associated with the CSI process” TS 36.213 v13.16.0
- Correction on the linkage between CSI-RS and CSI-IM for Class B TS 36.213CR0629
A CSI process can now be configured with both eMIMO-Type and eMIMO-Type2 (CLASS A+B or CLASS B+B), each with its own CSI-RS and CSI-IM resources, including up to two CSI-IM resources per type.
- “If the UE is configured with higher layer parameter eMIMO-Type and eMIMO-Type2, and eMIMO-Type is set to 'CLASS A', and eMIMO-Type2 is set to 'CLASS B'” TS 36.213 v14.17.0
- “and one CSI-RS resource (defined in Subclause 7.2.5) and one CSI-interference measurement (CSI-IM) resource (defined in Subclause 7.2.6) for eMIMO-Type2” TS 36.213 v14.17.0
NR CSI-IM is specified for the first time in Rel-15: CSI-IM resource sets for interference measurement in CSI resource settings, plus MAC CE activation/deactivation of semi-persistent CSI-IM resource sets.
- “CSI-IM resource for interference measurement as described in clause 5.2.2.4.” TS 38.214 v15.16.0
- “SP CSI-IM resource set ID: This field contains an index of CSI-IM-ResourceSet containing Semi Persistent CSI-IM resources” TS 38.321 v15.14.0
- “is used for interference measurement performed on CSI-IM.” TS 38.214 v15.16.0
Rel-16 NR CSI-IM text was extended for L1-SINR interference measurement, with CSI-IM usable for L1-SINR computation, updated time-restriction rules, and revised QCL typeD assumptions for CSI-IM resources.
- “for interference measurement the UE may be configured with NZP CSI-RS or CSI-IM resources.” TS 38.214 v16.17.0
- “the UE shall derive the interference measurements for computing the L1-SINR reported in uplink slot n based on the most recent” TS 38.214 v16.17.0
- “the interference measurements for computing CSI value based on periodic/semi-persistent CSI-IM measured only in OFDM symbol(s)” TS 38.214 v16.17.0
In TS 38.214, CSI-IM handling was extended and clarified: CSI-IM resource association and CRI mapping for NCJT (resource pairs/groups) were added, plus a clarification on the NCJT CSI-IM restriction.
- “If interference measurement is performed on CSI-IM, M+NM + N resources are configured in the corresponding csi-IM-ResourceSet.” TS 38.214 v17.16.0
- “Clarification on NCJT CSI-IM restriction” TS 38.214 v17.16.0
- “one CSI-IM occasion for each of the CSI-IM resources in the corresponding Resource Set for interference measurement” TS 38.214 v17.16.0
Rel-18 adds CSI-IM requirements: a single CSI-IM resource for CJT Type-II interference measurement, CSI-IM occasions restricted to cell DTX active periods, and CSI-IM occasion requirements for the new Doppler and CJT codebook reports.
- “If interference measurement is performed on CSI-IM, only one resource is configured in the corresponding csi-IM-ResourceSet.” TS 38.214 v18.11.0
- “in cell DTX active period of a serving cell if cell DTX is activated, occasion of CSI-IM and/or NZP CSI-RS for interference measurement” TS 38.214 v18.11.0
- Correction on aperiodic triggering offset of CSI-IM for Rel-18 Type-II Doppler codebook TS 38.214CR0671
CSI-IM gains new roles in Rel-19: SP CSI-IM resource sets can be activated/deactivated for LTM candidate cells via a new MAC CE, and CSI resource settings may reference CSI-IM for candidate-cell CSI acquisition.
- “the SP CSI-IM resource set for the candidate cell(s) indicated by CSI Resource Configuration ID2, if present” TS 38.321 v19.4.0
- “The UE shall deactivate all Semi-Persistent CSI-RS/CSI-IM resource sets of an LTM candidate cell upon (re-)configuration” TS 38.321 v19.4.0
- Correction on CSI-RS/CSI-IM for CSI acquisition on a candidate cell TS 38.214CR0754
Defining Specifications
3GPP specifications that define or reference CSI-IM, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 36.213 vj50 | LTE Physical Layer Procedures | Rel-19 read |
| TS 36.300 vj20 | E-UTRAN Radio Interface Protocol Architecture | Rel-19 read |
| TS 38.321 vj40 | NR MAC Protocol Specification | Rel-19 read |
| TR 38.889 vg00 | NR-based access to unlicensed spectrum study | Rel-16 read |