Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Radio Access Network

BFD-RS

BFD Reference Signal

Radio Access Network →

BFD-RS is a dedicated reference signal used in 5G NR for Beam Failure Detection, enabling UEs to monitor beam quality and detect failures by measuring specific BFD-RS resources.

Introduced
Rel-15
Where
Radio Access Network › NG-RAN (5G)
Specifications
3 specs
BFD-RS Description Purpose What changed Family Neighbours Detected Changes Specifications

Description

BFD-RS (Beam Failure Detection Reference Signal) is a specialized reference signal defined in 5G New Radio (NR) for the purpose of beam failure detection in beamformed communication systems. Unlike general-purpose reference signals like CSI-RS or SSB, BFD-RS is specifically configured for monitoring the quality of candidate beams that could potentially replace a failed serving beam. The signal is transmitted by the gNB on specific time-frequency resources configured via RRC signaling, allowing the UE to perform periodic measurements without requiring data transmission on those beams.

Architecturally, BFD-RS operates within the beam management framework of 5G NR's physical layer. The gNB configures one or more BFD-RS resources for the UE, each corresponding to a candidate beam. These resources include specific OFDM symbols, subcarriers, and periodicity information. The UE continuously monitors these configured BFD-RS resources while maintaining its primary connection on the serving beam. The monitoring process involves measuring reference signal received power (RSRP) or signal-to-interference-plus-noise ratio (SINR) on each BFD-RS resource and comparing these measurements against configured thresholds.

The beam failure detection mechanism works through a multi-step process. First, the UE monitors the quality of the serving beam using either the configured BFD-RS resources or other reference signals. When the serving beam quality falls below a configured threshold (Q_out), the UE starts a beam failure detection timer and begins evaluating candidate beams using their respective BFD-RS resources. If the UE identifies a candidate beam with quality above a recovery threshold (Q_in) before the timer expires, it can initiate beam failure recovery procedures. If no suitable candidate is found, the UE declares beam failure and may trigger radio link failure procedures.

Key components of the BFD-RS system include the BFD-RS resource configuration (specifying time-frequency resources, periodicity, and quasi-co-location information), beam failure detection thresholds (Q_out and Q_in), beam failure detection timer, and candidate beam identification logic. The BFD-RS resources are typically configured to be quasi-co-located with the corresponding candidate beams' control and data channels, ensuring that measurements on BFD-RS accurately reflect the quality of those beams for actual communication purposes.

In the broader network architecture, BFD-RS plays a crucial role in maintaining link reliability in high-frequency deployments where beamforming is essential. By providing dedicated measurement resources for candidate beams, BFD-RS enables faster and more reliable beam failure recovery compared to systems that rely on scanning all possible beams during failure events. This reduces service interruption time and improves overall system reliability, particularly in challenging radio environments with high mobility or blockage scenarios.

Purpose & Motivation

BFD-RS was created to address the specific challenges of beam management in 5G millimeter wave (mmWave) systems, where directional beamforming is essential due to high path loss and susceptibility to blockages. In traditional cellular systems operating at lower frequencies, omnidirectional or wide-beam transmission was sufficient for maintaining reliable connections. However, mmWave systems require narrow, directional beams to achieve adequate link budget, making them vulnerable to sudden beam failures caused by mobility, rotation, or environmental changes.

Previous approaches to link maintenance, such as radio link monitoring in LTE, were designed for wider coverage areas and slower channel variations. These systems used cell-specific reference signals (CRS) for monitoring but lacked the granularity and speed needed for beam-level failure detection in 5G. Without dedicated beam monitoring signals, UEs would need to constantly scan for alternative beams or wait for complete link failure before initiating recovery, resulting in unacceptable service interruption times for latency-sensitive applications.

The introduction of BFD-RS in 3GPP Release 15 specifically addressed these limitations by providing a standardized mechanism for proactive beam quality monitoring. It enables UEs to maintain a 'watch list' of candidate beams while actively using a serving beam, dramatically reducing the time required to switch to an alternative beam when the current one fails. This was particularly important for supporting use cases like enhanced mobile broadband (eMBB) and ultra-reliable low-latency communications (URLLC) in 5G, where even brief connection interruptions could degrade user experience or violate service level agreements.

What changed in its specifications

The latest release-to-release comparison of specifications that define BFD-RS. Each summary describes the whole specification, not only this term.

TS 38.133Rel-18 → Rel-19

Rel-19 adds low band carrier aggregation via switching and low-power wake-up receiver (LP-WUR) requirements to TS 38.133. It also adds ATG network support, intra-band non-collocated NR-CA receiver types, and multi-carrier BWP switch and SCell activation delay requirements.

Full comparison in TS 38.133 →

Technology family

MIMO and beam management · Radio Access Network › NG-RAN (5G)

  1. R99 Transmit diversity, TSTD
  2. Rel-7 MIMO
  3. Rel-8 CSI, DM-RS, MU-MIMO, PMI, RI, SDMA, SRS, SU-MIMO, TPMI
  4. Rel-10 CSI-RS, NZP CSI-RS
  5. Rel-11 CoMP, CSI-IM, QCL, UL CLTD, UL MIMO
  6. Rel-13 CRI, FD-MIMO
  7. Rel-15 Beam Level Mobility, Beam management, BFD, BFD-RS, BFR, PT-RS, TCI, ZP CSI-RS
  8. Rel-18 CJT

Also in this family (introduction release not pinned to a single defining specification): Beamforming

  • BFD-RS used together with BFD
    “the gNB configures the UE with beam failure detection reference signals (SSB or CSI-RS) and the UE declares beam failure when the number of beam failure instance indications” TS 38.300

Members and relations were proposed independently by several models and kept only where at least two agree; quotes are verified verbatim against the specifications. Release = first approved version of the defining specification.

Release Timeline

Detected Changes Across Releases

verified against 3GPP sources

Documented changes in 5 releases, each verified against the text of 3GPP specifications or approved change requests and shown with the exact wording. The release timeline above shows the same releases. A release without an entry has no documented change for this term.

Rel-15 introduced

TS 38.133 first specifies BFD-RS in Rel-15, with an abbreviation entry and evaluation-period scaling factors P for BFD-RS resources overlapping measurement gaps and SMTC occasions.

  • “BFD-RS BFD Reference Signal” TS 38.133 v15.35.0
  • “P = 1, when the BFD-RS resource is not overlapped with measurement gap and also not overlapped with SMTC occasion.” TS 38.133 v15.35.0
  • “Longer evaluation period would be expected if the combination of BFD-RS resource, SMTC occasion and measurement gap configurations does not meet pervious conditions.” TS 38.133 v15.35.0
Rel-16 specification text

Beam failure detection evaluation requirements are extended to operation with shared spectrum channel access, using new TEvaluate_BFD_SSB_CCA periods and a Qout_LR_SSB,CCA threshold.

  • “estimated over the last TEvaluate_BFD_SSB_CCA ms period becomes worse than the threshold Qout_LR_SSB,CCA within TEvaluate_BFD_SSB_CCA ms period” TS 38.133 v16.29.0
Rel-17 specification text

The BFD-RS evaluation requirements in TS 38.133 changed: the P value now depends on SMTC and gap overlap (xRP), low-mobility relaxation criteria apply, and the older measurement-gap-only formulas were removed.

  • “good serving cell quality criterion defined in clause 5.7.13.2 of TS 38.331 [2] is fulfilled for the serving cell configured with BFD-RS” TS 38.133 v17.23.0
  • “For a window W of duration max(TL1, MGRP_max), where MGRP_max is the maximum MGRP across all configured per-UE measurement gaps” TS 38.133 v17.23.0
  • “Ntotal is the total number of BFD-RS resource occasions within the window W, including those overlapped with measurement gap occasions or SMTC occasions” TS 38.133 v17.23.0
Rel-18 specification text

The evaluation-period rule for switching between BFD CD-SSB and NCD-SSB resources now also applies to SCG activation or deactivation, for UEs supporting ncd-SSB-BWP-Wor-r18.

  • “due to BWP switching or due to SCG activation or deactivation during one evaluation period” TS 38.133 v18.15.0
Rel-19 specification text

BFD requirements in TS 38.133 were extended: the evaluation window now includes switching pattern periodicity, BFD-RS occasions overlapping SDL/PCell ON durations are counted, and SBFD and HD-FDD RedCap conditions were added.

  • “For a window W of duration max(TL1, xRP_max, switching pattern periodicity)” TS 38.133 v19.6.0
  • “for the BFD monitoring on PCell, Ntotal also includes BFD-RS resource occasions that overlap with the SDL ON duration within the window,” TS 38.133 v19.6.0
  • “the requirements in this clause apply provided that all occasions of the BFD-RS resource are in the same type (i.e., SBFD or non-SBFD) of symbols.” TS 38.133 v19.6.0

Defining Specifications

3GPP specifications that define or reference BFD-RS, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 38.133 vk10 NR Radio Resource Management Requirements Rel-20 read
TS 38.174 vk00 NR Integrated Access and Backhaul Requirements Rel-20 read
TS 38.176 vj40 IAB Conformance Testing Rel-19 read