Menu
Latest
12 meetings · Prague, Jeju · 12–16 Oct
Reports
RAN1#126-bis · SA2#177

Glossary term · Physical Layer

FR1

Frequency Range 1

Physical Layer →

FR1 is the sub-6 GHz frequency range for 5G NR, spanning 410 MHz to 7125 MHz, which provides wide coverage for mobile broadband.

Introduced
Rel-15
Where
Radio Access Network › NG-RAN (5G)
Specifications
33 specs
Also in
Testing, User Equipment
FR1 Description Purpose What changed Family Neighbours Detected Changes Specifications

Description

Frequency Range 1 (FR1) is one of the two frequency ranges defined for 5G New Radio (NR) in 3GPP specifications. As per TS 38.101-1, FR1 encompasses the spectrum from 410 MHz to 7125 MHz, which includes many legacy bands used by 2G, 3G, and 4G, as well as new bands allocated for 5G. FR1 is often referred to as the sub-6 GHz range, although it extends slightly above 6 GHz to 7.125 GHz. This range is crucial for providing wide-area coverage and is the primary band for initial 5G deployments, offering a balance between capacity and coverage.

FR1 supports flexible numerology, with subcarrier spacings (SCS) of 15, 30, and 60 kHz. The choice of SCS depends on the deployment scenario and the trade-off between latency, coverage, and mobility support. For example, 15 kHz SCS is used for wide-area coverage, while 60 kHz SCS is used for low-latency applications. FR1 operates in both Frequency Division Duplex (FDD) and Time Division Duplex (TDD) modes, allowing operators to use their existing spectrum assets efficiently. The maximum channel bandwidth in FR1 is 100 MHz per carrier, which can be aggregated for higher data rates.

The physical layer design for FR1 includes support for massive MIMO, beamforming, and advanced modulation schemes such as 256-QAM. These features enable high spectral efficiency and throughput. FR1 also supports dynamic spectrum sharing (DSS) with LTE, allowing operators to deploy 5G NR in existing LTE bands without refarming spectrum. This is achieved through careful coordination of reference signals and scheduling between the two technologies.

In terms of architecture, FR1 is used by both the gNodeB (gNB) and the User Equipment (UE). The gNB transmits synchronization signals (SSB) and system information in FR1, and the UE performs cell search and random access accordingly. The smaller propagation loss in FR1 compared to FR2 (mmWave) allows for better coverage and penetration, making it suitable for rural and suburban areas as well as urban macrocells. However, the available bandwidth is limited compared to FR2, which can impact peak data rates.

FR1 is integral to the 5G system, providing the coverage layer that complements the capacity layer of FR2. It supports all 5G services, including enhanced Mobile Broadband (eMBB), Ultra-Reliable Low-Latency Communication (URLLC), and massive Machine-Type Communication (mMTC). The specifications for FR1 are continuously evolving, with new bands and features added in each release to improve performance and efficiency.

Purpose & Motivation

Frequency Range 1 (FR1) was defined to provide a dedicated spectrum range for 5G NR that balances coverage and capacity. Before 5G, cellular systems operated in various bands below 6 GHz, but they lacked a unified framework for flexible numerology and wide bandwidths. FR1 addresses this by defining a common set of parameters and requirements for sub-6 GHz operation, enabling global harmonization and economies of scale. It allows operators to reuse existing spectrum and infrastructure, facilitating faster 5G rollouts.

The primary motivation for FR1 was to ensure wide-area coverage for 5G services, as higher frequency bands (FR2) have limited propagation and are more suitable for dense urban hotspots. FR1 provides the necessary coverage for mobile broadband, IoT, and critical communications. It also supports features like dynamic spectrum sharing, which allows 5G and LTE to coexist in the same band, easing the transition for operators.

FR1 solves the problem of spectrum fragmentation by defining a flexible framework that can accommodate various channel bandwidths and duplex modes. It enables the use of advanced antenna techniques and high-order modulation, improving spectral efficiency. The definition of FR1 in 3GPP specifications ensures interoperability between vendors and allows UEs to support multiple bands within FR1, enhancing global roaming. Overall, FR1 is foundational to 5G, providing the coverage layer that makes ubiquitous 5G services possible.

What changed in its specifications

The latest release-to-release comparison of specifications that define FR1. Each summary describes the whole specification, not only this term.

TS 36.331Rel-18 → Rel-19

Rel-19 adds NTN-for-IoT Phase 3 and inter-RAT mobility from E-UTRAN to NR NTN, plus LTE-based 5G Broadcast Phase 2 changes. It also adds IMS disaster-roaming access barring, NTN-for-NR Phase 3 fields, and NR RRM Phase 5 items.

Full comparison in TS 36.331 →

Technology family

Frequency ranges and bands · Radio Access Network › NG-RAN (5G)

  1. Rel-13 LAA, LBT
  2. Rel-14 eLAA
  3. Rel-15 CAPC, FR1, FR2, NR operating band, Supplementary Uplink
  4. Rel-16 NR-U
  5. Rel-17 FR2-1, FR2-2
  6. Rel-18 FR2-NTN, SBFD

Also in this family (introduction release not pinned to a single defining specification): Sub-band, Superseding-band

  • FR1 coexists with FR2
    “The UE capabilities in NR rely on a hierarchical structure where each capability parameter is defined per UE, per duplex mode (FDD/TDD), per frequency range (FR1/FR2)” TS 38.300

Members and relations were proposed independently by several models and kept only where at least two agree; quotes are verified verbatim against the specifications. Release = first approved version of the defining specification.

Release Timeline

Detected Changes Across Releases

verified against 3GPP sources

Documented changes in 6 releases, each verified against the text of 3GPP specifications or approved change requests and shown with the exact wording. The release timeline above shows the same releases. A release without an entry has no documented change for this term.

Rel-15 introduced

FR1 gained specification content in Rel-15: its range was extended to 7.125 GHz, and FR1 signal levels, power levels and RF/demodulation test requirements were added or corrected.

  • Correction to support FR1 extension to 7.125 GHz TS 38.213CR0032
  • CR to TS 38.124 on FR1 extension TS 38.124CR0002
  • Correction to power level for FR1 RF tests TS 38.508-1CR0052
Rel-16 3 CRs

FR1 gained new requirements and configurations in Rel-16, e.g. additional RACH configurations for TDD FR1 and a one-slot periodic TRS configuration for FR1.

  • Introduction of additional RACH configurations for TDD FR1 TS 38.211CR0031
  • Introduction of one-slot periodic TRS configuration for FR1 under a certain condition TS 38.214CR0063
  • CR for 38.104 on PUSCH requirements with CP-OFDM and FR1 TS 38.104CR0063
Rel-17 3 CRs

Rel-17 added FR1-specific requirements and features, including DL 1024QAM for NR FR1, FR1 PUSCH 256QAM conformance requirements, and low-latency FR1 BS demodulation requirements.

  • Introduction of DL 1024QAM for NR FR1 TS 38.211CR0085
  • Introduction of conformance testing requirements for FR1 PUSCH 256QAM TS 38.104CR0372
  • Low latency and ultra-low BLER FR1 BS demodulation requirements TS 38.104CR0331
Rel-18 3 CRs

Rel-18 added NR support for dedicated spectrum below 5 MHz in FR1, with new demodulation, Tx intermodulation and PUCCH requirements in 38.104 and corresponding changes to the physical layer and RRC specifications.

  • Introduction of NR support for dedicated spectrum less than 5MHz for FR1 TS 38.331CR4525
  • BigCR on Demodulation requirements for less than 5MHz for TS 38.104 TS 38.104CR0602
  • Correction on beam determination in FR1 TS 38.214CR0666
Rel-19 3 CRs

FR1 gained new requirements and capabilities in Rel-19, including SIB1 PDSCH repetition for FR1 TN, an added 7 MHz FR1 channel bandwidth, and corrected FR1 PUSCH performance parameters.

  • Introduction of SIB1 PDSCH repetition for FR1 TN [Common_PDCCH_rep_TN] TS 38.300CR1085
  • CR to TS37.141 Introduction of 7 MHz NR FR1 channel bandwidth TS 37.141CR1098
  • Correction to FRC parameters for FR1 interlaced PUSCH performance requirements TS 38.104CR0705
Rel-20 2 CRs

Rel-20 CR corrects FR1 less-than-5MHz bandwidth demodulation requirements in 38.141-2 and updates SRS configuration in UL Tx switching test cases for FR1 enhancements.

  • CR on 38.141-2 Correction on less than 5MHz demodulation requirements (Rel-20) TS 38.141-2CR0739
  • Update SRS configuration in UL Tx switching test cases TS 38.133CR6965

Defining Specifications

3GPP specifications that define or reference FR1, with the latest known release. Sourced from the 3GPP document catalog — see methodology.

SpecificationTitleRelease
TS 36.331 vj40 E-UTRA Radio Resource Control (RRC) Protocol Rel-19 read
TS 37.114 vj00 EMC for Active Antenna System Base Stations Rel-19 read
TR 37.910 vj00 5G SRIT and NR RIT Self-Evaluation Report Rel-19 read
TR 37.911 vj00 3GPP 5G NTN Self-Evaluation Report Rel-19 read
TS 38.151 vj10 MIMO OTA Performance Requirements for NR UEs Rel-19 read
TS 38.161 vj30 UE TRP and TRS Requirements Rel-19 read
TS 38.211 vj50 NR Physical Channels and Signals Rel-19 read
TS 38.213 vj50 NR Physical Layer Control Procedures Rel-19 read
TS 38.307 vk10 Release-Independent NR UE Requirements Rel-20 read
TS 38.522 vk00 NR UE Conformance Test Applicability Rel-20 read
TS 38.523 vj40 UE Conformance Specification for 5G NR Rel-19 read
TS 38.551 vj10 NR MIMO OTA Performance Requirements Rel-19 read
TS 38.561 vj20 NR FR1 OTA TRP/TRS Conformance Testing Rel-19 read
TS 38.753 vj00 Spatial Channel Model Study for NR Demodulation Rel-19 read
TS 38.761 vj00 MIMO OTA Performance Measurements for UE Rel-19 read
TS 38.762 vj10 NR FR1 MIMO OTA Dynamic Test Methodology Rel-19 read
TS 38.774 vj20 RF Requirements for Low-Power Wake-up Signal and Receiver Rel-19 read
TR 38.785 vh00 UE radio transmission for enhanced NR sidelink Rel-17 read
TR 38.786 vi20 Technical Report for NR Sidelink Evolution Rel-18 read
TS 38.787 vj00 UE Radio Transmission for Sidelink CA in ITS Band Rel-19 read
TR 38.810 vg70 NR OTA Test Methods Study Rel-16 read
TR 38.820 vg10 NR; 7-24 GHz Frequency Range Study Rel-16 read
TS 38.827 vg80 NR MIMO OTA Radiated Metrics & Test Methodology Rel-16 read
TR 38.834 vh20 NR FR1 TRP/TRS Test Methodology Rel-17 read
TR 38.838 vh00 Study on XR Evaluations for NR Rel-17 read
TR 38.844 vi00 Efficient utilization of licensed spectrum Rel-18 read
TR 38.868 vh00 Optimizations of pi/2 BPSK uplink power in NR Rel-17 read
TR 38.869 vi00 Study on low-power wake up signal and receiver for NR Rel-18 read
TS 38.870 vj50 Enhanced OTA Test Methods for NR TRP and TRS Rel-19 read
TR 38.884 vi20 Technical Report Rel-18 read
TR 38.886 vg30 NR V2X UE Radio Transmission & Reception Rel-16 read
TR 38.889 vg00 NR-based access to unlicensed spectrum study Rel-16 read
TR 38.903 vj40 NR UE Test Tolerances and Uncertainties Rel-19 read