Description
Frequency Range 2 (FR2) is the millimeter-wave (mmWave) frequency range defined for 5G New Radio (NR) in 3GPP specifications. As per TS 38.101-2, FR2 spans from 24.25 GHz to 71 GHz, although the initial focus was on bands around 28 GHz and 39 GHz. FR2 provides significantly larger bandwidths compared to FR1, enabling multi-gigabit peak data rates and ultra-low latency. However, the propagation characteristics at these frequencies result in higher path loss, poor penetration through obstacles, and limited coverage, necessitating dense small-cell deployments and advanced beamforming techniques.
FR2 supports subcarrier spacings of 60, 120, and 240 kHz, which are larger than those in FR1 to combat phase noise and support wider bandwidths. The maximum channel bandwidth in FR2 is 400 MHz per carrier, and with carrier aggregation, even higher bandwidths can be achieved. FR2 operates primarily in TDD mode due to the difficulty of implementing FDD at mmWave frequencies. The use of massive MIMO and beamforming is essential in FR2 to overcome high path loss; the gNB and UE use phased array antennas to steer beams and maintain link budget.
The physical layer design for FR2 includes support for flexible beam management, beam failure recovery, and multi-beam operation. Synchronization signals and system information are transmitted via beams, and the UE performs beam sweeping during initial access. FR2 also supports dual connectivity with FR1 (EN-DC or NR-DC), where FR1 provides the coverage layer and FR2 provides the capacity layer. This architecture allows seamless mobility and service continuity.
In terms of deployment, FR2 is typically used in dense urban areas, stadiums, and hotspots where high capacity is needed. The small coverage radius of FR2 cells (often less than 200 meters) requires a dense network of small cells, which increases deployment costs. However, the large bandwidths available in FR2 make it ideal for fixed wireless access (FWA) and high-speed backhaul. FR2 also supports advanced features like integrated access and backhaul (IAB) to reduce fiber deployment costs.
FR2 is a key enabler for the most demanding 5G use cases, such as ultra-high-definition video streaming, virtual reality, and industrial automation. Its specifications continue to evolve, with new bands and features added in each release to improve spectral efficiency and coverage. Despite its challenges, FR2 is essential for delivering the extreme capacity and low latency promised by 5G.
Purpose & Motivation
Frequency Range 2 (FR2) was defined to unlock the vast spectrum available at millimeter-wave frequencies for 5G NR. Before 5G, cellular systems were confined to sub-6 GHz bands, which offered limited bandwidth and could not support the multi-gigabit data rates envisioned for 5G. FR2 addresses this by providing a framework for operating in the 24.25–71 GHz range, where large contiguous bandwidths are available. This enables extreme capacity and low latency, making it suitable for dense urban hotspots and specialized applications.
The motivation for FR2 was to meet the International Mobile Telecommunications (IMT)-2020 requirements for peak data rates (20 Gbps) and user-experienced data rates (100 Mbps). FR1 alone cannot achieve these targets due to spectrum scarcity. FR2 also supports new use cases like fixed wireless access and industrial IoT, where high throughput and low latency are critical. However, the propagation challenges of mmWave required innovative solutions like beamforming and dense small cells, which are integral to FR2 specifications.
FR2 solves the problem of spectrum shortage by opening up new bands for mobile communications. It also drives innovation in antenna technology and network architecture. The definition of FR2 in 3GPP ensures global harmonization and interoperability, allowing UEs to roam across different FR2 deployments. While FR2 deployments are still growing, it is a cornerstone of the 5G vision for ubiquitous high-speed connectivity.
What changed in its specifications
The latest release-to-release comparison of specifications that define FR2. Each summary describes the whole specification, not only this term.
Rel-19 adds NTN-for-IoT Phase 3 and inter-RAT mobility from E-UTRAN to NR NTN, plus LTE-based 5G Broadcast Phase 2 changes. It also adds IMS disaster-roaming access barring, NTN-for-NR Phase 3 fields, and NR RRM Phase 5 items.
Full comparison in TS 36.331 →Rel-19 changed TS 38.211 for sub-band full duplex (SBFD). It added PRACH and PDSCH resource mapping text covering SBFD symbols and uplink or downlink sub-bands.
Full comparison in TS 38.211 →Technology family
Frequency ranges and bands · Radio Access Network › NG-RAN (5G)
- Rel-13 LAA, LBT
- Rel-14 eLAA
- Rel-15 CAPC, FR1, FR2, NR operating band, Supplementary Uplink
- Rel-16 NR-U
- Rel-17 FR2-1, FR2-2
- Rel-18 FR2-NTN, SBFD
Also in this family (introduction release not pinned to a single defining specification): Sub-band, Superseding-band
- FR2 extended by FR2-1
“For BS type 2-O operating in FR2-1, the OTA out-of-band blocking requirement apply from 30 MHz to FUL,low – 1500 MHz” TS 38.104
- FR2 extended by FR2-2
“For BS type 2-O operating in FR2-2, the OTA out-of-band blocking requirement apply from 30 MHz to FUL,low – 3500 MHz” TS 38.104
- FR2 coexists with FR1
“The UE capabilities in NR rely on a hierarchical structure where each capability parameter is defined per UE, per duplex mode (FDD/TDD), per frequency range (FR1/FR2)” TS 38.300
- FR2 extended by FR2-NTN
“To extend the NR downlink coverage for NTN operating in, for FR1-NTN and FR2-NTN bands” TS 38.300
Members and relations were proposed independently by several models and kept only where at least two agree; quotes are verified verbatim against the specifications. Release = first approved version of the defining specification.
Release Timeline
Detected Changes Across Releases
verified against 3GPP sourcesDocumented changes in 6 releases, each verified against the text of 3GPP specifications or approved change requests and shown with the exact wording. The release timeline above shows the same releases. A release without an entry has no documented change for this term.
Rel-15 specifications and CRs add FR2-specific requirements, test cases and procedures, including FR2 OTA testing, spurious emission measurement grids, and a corrected PDSCH reception procedure in FR2.
- “specified at the antenna connector(s) of the UE for the bands operating on frequency range 1 and over the air of the UE for the bands operating on frequency range 2” TS 38.521-3 v15.4.1
- Correction on UE receiving PDSCH procedure in FR2 TS 38.214CR0037
- “Correction to FR2 Spurious TC and introduction of TRP measurement grid requirement” TS 38.521-2 v15.4.0
Rel-16 changed FR2 requirements and capabilities, adding FR2 DL 256QAM, FR2 inter-band DL CA, intra-band non-contiguous UL CA, new MPR, and FR2 test cases for UL CA and UL MIMO.
- CR to TS 38.101-2: Introduction of FR2 DL 256QAM TS 38.101-2CR0193
- Introduction of FR2 inter-band DL CA TS 38.101-2CR0237
- FR2 intra-band non-contiguous UL CA feature TS 38.101-2CR0252
Rel-17 extended FR2 with new requirements, capabilities and test cases, including FR2 FBG2 CA bandwidth classes, FR2 HST BS demodulation requirements, and power class 6 UE requirements for HST FR2.
Rel-18 changed FR2 requirements and capabilities, including HST multi-panel RF requirements, FR2 multi-Rx, UL MIMO EVM measurement, FR2 CA BW class capabilities and new FR2 test cases.
- Feature CR for RF requirements of FR2 HST multi-panel operation TS 38.101-2CR0649
- Feature CR for FR2 multi-Rx TS 38.101-2CR0665
- Introduction of Rel-18 HST FR2 RRM enhancements TS 38.331CR4428
FR2 requirements and test coverage changed in Rel-19, including FR2 RF requirements for NR_MIMO_Ph5 and LP-WUS, and FR2 intra-band CA fallback requirements in test specs.
- CR on FR2 RF requirements for NR_MIMO_Ph5 TS 38.101-2CR0823
- LP-WUS feature CR, FR2 TS 38.101-2CR0824
- “if the field partialFR2-FallbackRX-Req is present, for each FR2 intra-band CA configuration with multiple sub-blocks” TS 38.521-2 v19.4.1
FR2 requirements changed: the FR2 intra-frequency L1-RSRP measurement period for LTM was corrected, and FR2 test parameters and channel models were updated for beam management and multi-Rx.
Defining Specifications
3GPP specifications that define or reference FR2, with the latest known release. Sourced from the 3GPP document catalog — see methodology.
| Specification | Title | Release |
|---|---|---|
| TS 36.331 vj40 | E-UTRA Radio Resource Control (RRC) Protocol | Rel-19 read |
| TR 37.910 vj00 | 5G SRIT and NR RIT Self-Evaluation Report | Rel-19 read |
| TS 38.151 vj10 | MIMO OTA Performance Requirements for NR UEs | Rel-19 read |
| TS 38.211 vj50 | NR Physical Channels and Signals | Rel-19 read |
| TS 38.213 vj50 | NR Physical Layer Control Procedures | Rel-19 read |
| TS 38.307 vk10 | Release-Independent NR UE Requirements | Rel-20 read |
| TS 38.509 vj00 | 5GS UE Special Conformance Test Functions | Rel-19 read |
| TS 38.522 vk00 | NR UE Conformance Test Applicability | Rel-20 read |
| TS 38.523 vj40 | UE Conformance Specification for 5G NR | Rel-19 read |
| TS 38.551 vj10 | NR MIMO OTA Performance Requirements | Rel-19 read |
| TS 38.753 vj00 | Spatial Channel Model Study for NR Demodulation | Rel-19 read |
| TS 38.761 vj00 | MIMO OTA Performance Measurements for UE | Rel-19 read |
| TS 38.771 vj00 | FR2-1 OTA Testing for STxMP UEs | Rel-19 read |
| TS 38.774 vj20 | RF Requirements for Low-Power Wake-up Signal and Receiver | Rel-19 read |
| TR 38.785 vh00 | UE radio transmission for enhanced NR sidelink | Rel-17 read |
| TR 38.786 vi20 | Technical Report for NR Sidelink Evolution | Rel-18 read |
| TR 38.810 vg70 | NR OTA Test Methods Study | Rel-16 read |
| TR 38.820 vg10 | NR; 7-24 GHz Frequency Range Study | Rel-16 read |
| TS 38.827 vg80 | NR MIMO OTA Radiated Metrics & Test Methodology | Rel-16 read |
| TS 38.831 vg10 | UE RF Requirements for FR2 Enhancements | Rel-16 read |
| TR 38.838 vh00 | Study on XR Evaluations for NR | Rel-17 read |
| TR 38.868 vh00 | Optimizations of pi/2 BPSK uplink power in NR | Rel-17 read |
| TR 38.869 vi00 | Study on low-power wake up signal and receiver for NR | Rel-18 read |
| TR 38.884 vi20 | Technical Report | Rel-18 read |
| TR 38.886 vg30 | NR V2X UE Radio Transmission & Reception | Rel-16 read |
| TR 38.889 vg00 | NR-based access to unlicensed spectrum study | Rel-16 read |
| TR 38.903 vj40 | NR UE Test Tolerances and Uncertainties | Rel-19 read |